Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Well, if you flash to my special super bios you will be forced to upgrade to x58. The chances of your board surviving the flash are slim to none. End result....you will have a faster rig.
Ill make a deal with you, you get an X58 board and Ill give you a chip for it.
Last edited by OC Nub; 08-20-2010 at 12:24 PM.
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Yes!!! Whatever it takes to get you to upgrade my friend.
i got some spare x58 boards andressergio
i got some spare ram too
p45 sucks
maximus IV extreme gtx580
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52v gtx285 ftw sli
OCZ3RPR1866LV6GK hypers
dfi ut p35 rampage extreme
gigabut p35c-ds3r bios suks
gigabut x38-d6q dead thank god
ballistix 8500 1240mhz@2.02v
Sergio, you were meant to be on i7!!!!
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
I cant give you this chip, but I am serious about a 920, I have 2 and dont need them both. You tell me when you order a board and Ill bubble wrap the chip and send it out.
maximus IV extreme gtx580
gigabut p67-ud7
p67 sabertooth
2500k+2600k
antec 1200watt
EVGA classified 760
920 Batch# 3849B018 4.985ghz@1.52v gtx285 ftw sli
OCZ3RPR1866LV6GK hypers
dfi ut p35 rampage extreme
gigabut p35c-ds3r bios suks
gigabut x38-d6q dead thank god
ballistix 8500 1240mhz@2.02v
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
guys where's the tRC that CPUZ shows ? there's a specific value to each speed and radaja just told me that could be the reason and he maybe true...but i cant find it on bios
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
maybe your p45 dont have it.i know my ST needed tRC set manually or it would set 20 or 21 instead of the SPD of 37
Channel A & B
Channel A Timing Settings [Press Enter]:
Cas Latency Time........................[10]
tRCD....................................[10]
tRP.....................................[10]
tRAS...................................[24]
>>>>> Advanced Timing Control
tRC....................................[37] this is it on my bios
tRRD...................................[4]
tWTR...................................[5]
tWR....................................[10]
tWTP...................................[22]
tWL....................................[8]
tRFC...................................[74]
tRTP...................................[5]
tFAW...................................[20]
Command Rate (CMD)......................[ 1T ]
Static tRD......................................[12]
_________________________________________________
............................ImAcOmPuTeRsPoNgE............................
[SIGPIC][/SIGPIC]
MY HEATWARE 76-0-0
Hello everybody,
I just installed a used GA-EP45-UD3P with Bios F10 and having a problem with a long beep at intitial powerup. I press the power button on my compuer and as soon as it gets to the part where the monitor gets a signal I hear a long 3 second beep and then the system goes into loading bios and then straight to XP and everything is fine. I encoded four movies last night and everything went fine plus I get no BSOD's while I'm using the computer. The computer runs really good while it's on.
I checked all connections and a voltages are all fine.
I'm using a E7500 CPU with Kingston DDR2 SDRAM DDR2 800 (PC2 6400) value ram.
In Bios everything is in Optimized State.
Performance Enchance --Standard
mCH frequency Latch --Auto
System Memory Muli --Auto
Mem Freq 800
Cas Latency Time --6
tRCD --6
tRP --6
tras --18
Load Line Calib -Disabled
All Volts are set to --Normal
No-Execute Memory -Enabled
CPU-Z reads:
Dram Freq 400.MHz
FSB 2:3
6 6 6 18 tRFC-52
Command Rate 2T
1.8V
I'm wondering if the board just doesn't like the value ram but the system is running great with it except for that long beep at bootup.
Thanks
That's what I was thinking.
Is this ram good for the board
http://www.newegg.com/Product/Produc...82E16820231194
In two months I will be getting a Q9650 so I want ram that will work with this chip really good to.
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
My board is Revision 1.0, Are there any settings I can use to get rid of the long Beeeeeep? Maybe the board has configured the ram wrong.
Hello everybody,
I just installed a used GA-EP45-UD3P with Bios F10 and having a problem with a long beep at intitial powerup. I press the power button on my compuer and as soon as it gets to the part where the monitor gets a signal I hear a long 3 second beep and then the system goes into loading bios and then straight to XP and everything is fine. I encoded four movies last night and everything went fine plus I get no BSOD's while I'm using the computer. The computer runs really good while it's on.
I checked all connections and a voltages are all fine.
I'm using a E7500 CPU with Kingston DDR2 SDRAM DDR2 800 (PC2 6400) value ram.
In Bios everything is in Optimized State.
Performance Enchance --Standard
mCH frequency Latch --Auto
System Memory Muli --Auto
Mem Freq 800
Cas Latency Time --6
tRCD --6
tRP --6
tras --18
Load Line Calib -Disabled
All Volts are set to --Normal
No-Execute Memory -Enabled
CPU-Z reads:
Dram Freq 400.MHz
FSB 2:3
6 6 6 18 tRFC-52
Command Rate 2T
1.8V
I'm wondering if the board just doesn't like the value ram but the system is running great with it except for that long beep at bootup.
Thanks
Last edited by TaranScorp; 08-21-2010 at 03:21 PM.
Good news.. Good news...
Installed Q9650 into USB3P, ported over my x48 Blackops 24/7 (Q9650/445 FSB) settings to USB3P bios, and everything worked the first time. This was far easier than I thought it would be.
Once I get a real cooling solution, I will explore Q9650-USB3P-action more fully.
XmX
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
_________________________________________________
............................ImAcOmPuTeRsPoNgE............................
[SIGPIC][/SIGPIC]
MY HEATWARE 76-0-0
Intel Core i9-7980XE@ 4.8GHz 18C/18TH (Direct Die Contact)
ASRock X299 OC Formula
ADATA XPG SPECTRIX D80 (4x8GB) DDR4-3800C17 B-Die
1x Intel Optane SSD 905P 480GB
4x HP EX950 NVMe 2TB on ASRock ULTRA M.2 CARD
EVGA RTX 2080TI KINGPIN 2190/8000 Stock Cooling AIO 240
SilverStone ST1500W-TI TITANIUM
Alphacool Custom Water Cooling
Bookmarks