** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**pmacdonald** · 08-08-2009, 12:56 PM

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.00GHz..........................[ 500 x 8.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]

 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 266      ]
System Memory Multipler.........................[ 2.00D    ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]

 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15    ]...................[ 1.350   ]
CPU Termination   [ 1.20    ]...................[ 1.280   ]
CPU PLL           [ 1.50    ]...................[ 1.570   ]
CPU Reference     [ 0.760   ]...................[ 0.780   ]
 
MCH Core          [ 1.100   ]...................[ 1.360   ]
MCH Reference     [ 0.760   ]...................[ 0.750   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.110   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 1.900   ]
DRAM Termination  [ 0.900   ]...................[ 0.960   ]
Channel A Ref     [ 0.900   ]...................[ 0.960   ]
Channel B Ref     [ 0.900   ]...................[ 0.960   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Enabled ]

I can't seem to get above 4GHz. I've tried a $|-|!T|_()/-\|) of changes but none have even allowed me to boot up. What changes should I make to the above settings to get to 4.25GHz (or anything 4GHz+).

**gugle** · 08-08-2009, 01:07 PM

LLC on, is dangerous in cpu 45nm ?

**thebluemeanie1** · 08-08-2009, 04:55 PM

Originally Posted by gugle

LLC on, is dangerous in cpu 45nm ?

I'de say no. I use it all the time and it hasn't done my CPU any harm.

It can't be any worse than a vDroop mod.

**fatguy1992** · 08-08-2009, 05:33 PM

I'm so pissed off at Gigabyte right now, why the

did they make the max vcore for Celeron's only 1.4vcore? WTF on a E8600 you can do to 2.3vcore, but no, on the older CPUs (that need more) you only get 1.4vcore and who only needs 1.4vcore, its nothing. May as well not even raise it at all.

I still got 5.2GHz with only 1.376vcore, which I think is pretty good. Howwever ofc I need 1.8vcore at least so I can do some 6.5GHz+ benching.

Does anyone know a way around this and would a new BIOS help etc? Or is there a good reason why they did this?

Thanks

**BlindFreddie** · 08-08-2009, 11:19 PM

Cross-post with: http://www.xtremesystems.org/forums/...19&postcount=1(Beep codes during POST - Are they made by CPU running, or m/b hardware? Q9650, P45mb).

I've got some major hardware failure problems with my Q9650/UD3R system, and I don't know exactly what has happened or why. More details in above post.
I was running with FSB=468, VNB=1.48 when things went awry. I asked in the post re max safe VNB for P45s, but no-one has answered (can't fit everything in a title). Hoping you guys might help ...

Oh, and I've never lifted the heatpipe assy off the UD3R, but I did have a 120mm fan leaning against the TRUE, blowing straight onto the P45.

My dilemma is also that I don't want to buy more LGA775 stuff now, but to test which components are faulty/saleable I need more DDR2 RAM and another CPU would be helpful.

**techguy2k5** · 08-09-2009, 07:13 AM

Originally Posted by BlindFreddie

Cross-post with: http://www.xtremesystems.org/forums/...19&postcount=1(Beep codes during POST - Are they made by CPU running, or m/b hardware? Q9650, P45mb).

I've got some major hardware failure problems with my Q9650/UD3R system, and I don't know exactly what has happened or why. More details in above post.
I was running with FSB=468, VNB=1.48 when things went awry. I asked in the post re max safe VNB for P45s, but no-one has answered (can't fit everything in a title). Hoping you guys might help ...

Oh, and I've never lifted the heatpipe assy off the UD3R, but I did have a 120mm fan leaning against the TRUE, blowing straight onto the P45.

My dilemma is also that I don't want to buy more LGA775 stuff now, but to test which components are faulty/saleable I need more DDR2 RAM and another CPU would be helpful.

I don't think 1.48V vNB/vMCH is too high for P45. I've run 1.5 on my previous Gigabyte P35-DS3L board which has a tiny NB cooler.

Reset your BIOS and try to get it to POST. If it still can't then you've got something loose somewhere or a faulty component. Start with the easy stuff first (RAM, expansion cards). Sometimes disconnecting and re-connecting your PSU cables to the mobo can help.

**techguy2k5** · 08-09-2009, 08:27 AM

Really liking this board so far. My new Q9550 is giving fantastic preliminary results on it. 3.6GHz @ stock volts (425x8.5) and only a vMCH bump to 1.3 delivers a full pass in OCCT Linpack. Shooting for 4GHz on air (OCZ Vendetta 2 push-pull w/stock fan & Scythe 1900 RPM 110CFM fan). VTT, PLL, & GTL Ref @ stock still. Temps in the mid-60's in OCCT in a hot apartment with practically worthless AC.

**techguy2k5** · 08-09-2009, 09:36 AM

4GHz (8.5x471) now OCCT Linpack stable @ 77 degrees. vMCH 1.4, vCore 1.375 BIOS (1.33 Windows), LLC enabled, vTT 1.3V, all else stock.

That was the easiest overclock ever.

**OC Nub** · 08-09-2009, 11:41 AM

Put my q9550 back in for more testing today. Have had more time now to learn this mobo. This is where I am at now. Core 2 sensor is bugged but if at least one sensor wasn't off I would think something was wrong.

**Homeless2** · 08-09-2009, 12:51 PM

Originally Posted by OC Nub

Put my q9550 back in for more testing today. Have had more time now to learn this mobo. This is where I am at now. Core 2 sensor is bugged but if at least one sensor wasn't off I would think something was wrong.

My core2 is like that also. I'm going to reapply thermal paste next week to see if anything changes. Also may I ask what settings you are using to get that oc? I can't get 500fsb stable no matter what I do w/ my chip.

**OC Nub** · 08-09-2009, 12:56 PM

Originally Posted by Homeless2

My core2 is like that also. I'm going to reapply thermal paste next week to see if anything changes. Also may I ask what settings you are using to get that oc? I can't get 500fsb stable no matter what I do w/ my chip.

I will try and make a template tonight for these settings.

**techguy2k5** · 08-09-2009, 06:22 PM

Finally hit 20k in 3dmark 06. Not bad for a single GTX 285 and a Q9 on air, IMHO.

**OC Nub** · 08-09-2009, 06:45 PM

Originally Posted by Homeless2

My core2 is like that also. I'm going to reapply thermal paste next week to see if anything changes. Also may I ask what settings you are using to get that oc? I can't get 500fsb stable no matter what I do w/ my chip.

Sorry I havent learned to use the code yet. You can try this using 200d pl9 standard or turbo and trfc auto depending on your ram.

******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Turbo ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.5 ]
CPU Frequency 4.35GHz............................[ 512 x 8.5]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 512 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 800mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Turbo ]
Extreme Memory Profile (X.M.P)..................[ Auto ]
(G) MCH Frequency Latch.........................[ 333 ]
System Memory Multipler.........................[ 2.40B ]
Memory Frequency 1066...........................[ 1228? ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]

******Advanced Timing Control******

tRRD[4].........................................[ auto ]
tWTR[4].........................................[ auto ]
tWR[13].........................................[ auto ]
tRFC[68] .......................................[ 50 ]
tRTP[4].........................................[ auto ]
Command Rate (cmd)[0]...........................[ Auto ]

******Channel A Timing Settings******

Static tRead Value [ 9 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value [ 9 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.1875 ]...................[ 1.40 ]
CPU Termination [ 1.20 ]...................[ 1.360 ]
CPU PLL [ 1.50 ]...................[ 1.570 ]
CPU Reference [ 0.760 ]...................[ 0.886 ]

MCH Core [ 1.100 ]...................[ 1.460 ]
MCH Reference [ 0.760 ]...................[ 0.901 ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ 1.500 ]
ICH Core [ 1.100 ]...................[ 1.200 ]

DRAM Voltage [ 1.800 ]...................[ 2.16 ]
DRAM Termination [ 0.900 ]...................[ Auto ]
Channel A Ref [ 0.900 ]...................[ Auto ]
Channel B Ref [ 0.900 ]...................[ Auto ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled

Nice score techguy

**thebluemeanie1** · 08-09-2009, 08:27 PM

Originally Posted by OC Nub

Sorry I havent learned to use the code yet. You can try this using 200d pl9 standard or turbo and trfc auto depending on your ram.

To use code click the number sign(pound sign) under message while in the advanced reply to thread page. Upon clicking it [CODE][CODE] will appear, the second code will have / before CODE.

Enter the message you want to be in code between the two sets of [CODE] and that's it.

It should look like [CODE]message here[CODE] but with a / before the second CODE and after the bracket.

**OC Nub** · 08-10-2009, 07:02 AM

Thank you. I will try that for sure. After spending months on this thread I felt stupid asking.

**andressergio** · 08-10-2009, 07:18 AM

Originally Posted by OC Nub

Thank you. I will try that for sure. After spending months on this thread I felt stupid asking.

Why so mate we always learn something everyday

Cheers all

Sergio

**bluestang** · 08-10-2009, 09:23 AM

Originally Posted by bluestang

Just got a new build at work for myself to play with. Had to order everything from TigerDirect on company account, so options were limited. (my work is cheap, but I managed to at least get this)...

GA-EP45T-UD3LR (F5 BIOS)
E7500 (1.200 VID)
OCZ DDR3 PC3-12800 XMP DDR3-1600 on sale at TigerDirect.com

Anyone have a 500 FSB BIOS setting they can share. Leeghoofd, I think you used this board in your E6300, E7400, E8600 cache battle. Can you please post some settings you used? Thanks!

Originally Posted by hank123

dude if you get that ram over 1600Mhz with out using a 3:5 divider i will give you a high 5. This mobo sucks ass for DDR3.

Dude running up to 500FSB is cake on this mobo. Drop the divider and run up the FSB. No problem lol really that easy!

Originally Posted by bluestang

Can you post some of your BIOS Settings? That would be great!

Right now I'm just starting off so I'm doing 10x400FSB with the 4.0A divider for 1600MHZ @ 7-7-7-28-PL8 with 1.96v in BIOS, LLC Enabled, 1.325v BIOS, 1.34v MCH, 1.24v VTT, all other on normal and Ref's on on auto for now.

Any help you can give me on 500FSB settings would be much appreciated

@Hank,
So far here is where I'm at. I'm wondering if my core temps are screwy. CPU temp is @ 67c max when core temps are at 56c max...Does that make sense? I know they're stuck at a min of 40c, so that sucks too.

**Homeless2** · 08-10-2009, 09:43 AM

Originally Posted by OC Nub

Sorry I havent learned to use the code yet. You can try this using 200d pl9 standard or turbo and trfc auto depending on your ram.

******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Turbo ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.5 ]
CPU Frequency 4.35GHz............................[ 512 x 8.5]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 512 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 800mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Turbo ]
Extreme Memory Profile (X.M.P)..................[ Auto ]
(G) MCH Frequency Latch.........................[ 333 ]
System Memory Multipler.........................[ 2.40B ]
Memory Frequency 1066...........................[ 1228? ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]

******Advanced Timing Control******

tRRD[4].........................................[ auto ]
tWTR[4].........................................[ auto ]
tWR[13].........................................[ auto ]
tRFC[68] .......................................[ 50 ]
tRTP[4].........................................[ auto ]
Command Rate (cmd)[0]...........................[ Auto ]

******Channel A Timing Settings******

Static tRead Value [ 9 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value [ 9 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.1875 ]...................[ 1.40 ]
CPU Termination [ 1.20 ]...................[ 1.360 ]
CPU PLL [ 1.50 ]...................[ 1.570 ]
CPU Reference [ 0.760 ]...................[ 0.886 ]

MCH Core [ 1.100 ]...................[ 1.460 ]
MCH Reference [ 0.760 ]...................[ 0.901 ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ 1.500 ]
ICH Core [ 1.100 ]...................[ 1.200 ]

DRAM Voltage [ 1.800 ]...................[ 2.16 ]
DRAM Termination [ 0.900 ]...................[ Auto ]
Channel A Ref [ 0.900 ]...................[ Auto ]
Channel B Ref [ 0.900 ]...................[ Auto ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled

Nice score techguy

Thanks

**gugle** · 08-10-2009, 05:10 PM

What could be the options in the bios, a UD3P + Q9550 stable at 4.5 GHz?

thanks

**18 is # 1** · 08-10-2009, 06:06 PM

Sorry if this is a bit noobish, how do I copy and paste my bios settings like:

Originally Posted by Hoss331

Try this one.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.05GHz...........................[ 450 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 450      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 800mv   ]
PCI Express Clock Drive.........................[ 900mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 900      ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 4       ]
tRCD............................................[ 4       ]
tRP.............................................[ 4       ]
tRAS............................................[ 12      ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 3       ]
tWTR[3].........................................[ 3       ]
tWR[6]..........................................[ 6       ]
tRFC[54]........................................[ 52      ]
tRTP[3].........................................[ 3       ]
Command Rate (cmd)[0]...........................[ 2T      ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1066    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1066    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15    ]...................[ 1.37500 ]
CPU Termination   [ 1.20    ]...................[ 1.280   ]
CPU PLL           [ 1.50    ]...................[ 1.500   ]
CPU Reference     [ 0.760   ]...................[ 0.835   ]
 
MCH Core          [ 1.100   ]...................[ 1.280   ]
MCH Reference     [ 0.760   ]...................[ 0.850   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.050   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 2.100   ]
DRAM Termination  [ 0.900   ]...................[ 1.050   ]
Channel A Ref     [ 0.900   ]...................[ 1.050   ]
Channel B Ref     [ 0.900   ]...................[ 1.050   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

**Hoss331** · 08-10-2009, 07:51 PM

Keep a copy of the template in a txt file, then when you want to post it click the # symbol on the reply page and paste.

**TooFastForYa** · 08-10-2009, 08:20 PM

Anyone know where I can get a hold of a rev 1.0 UD3P?
Thanks

**dekruyter** · 08-11-2009, 11:15 AM

Been overclocking an EP45-UD3R, w/ a Q9550, w/ 1.25 VID.

Before I go crazy, I'm going to stop @ 3.4; I got to 3.5 w/ some somewhat crazy numbers, but I just can't figure it out going above 3.5. Temps are not a problem, just stability in IDT, OCCt, Prime95. I read and tried alot of voltage settings. Oh well, truthfully, I only needed to go to 3.4 for gaming and every day use. I thin my 800 speed G.Skill ram held me up.

.

**bluestang** · 08-11-2009, 11:25 AM

Have a temp issue I need help figuring out. I have a E7500 in a GA-EP45T-UD3LR running at 4 GHz (8x500FSB) and my CPU Temp reads about 10 degrees hotter under testing than my Core #1 and #2 temps do. For instance CPU=65c and Core 1/2=55c This is the case in both the newest version of Everest Ultimate, HWMonitor (Pro and free), and Speedfan. I know the E7x00 IHS are only glued not soldered so I'm not sure. Also, both my core temps only go down to 40c at idle, so evidently I have stuck sensors too, although my CPU temp will go down to 25c at idle. Should I be concerned?

**Aynjell** · 08-11-2009, 12:04 PM

I can't go past 300 FSB, I refuse to lower my memory anymore and it doesn't even appear to help the OC any... I'm stuck at 3.9 for the time being... but I'm sure just like I was stuck at 3.64 before, some experimentation might cure this. As of right now though, I'm tempted to start toying with timings and other things. I can pull 22,800 in 3DMark 05, at the default test settings. Is this good, or bad (or about even for that matter)?

This is at 3.9Ghz, DDR2-1000 (5-5-5-15) and a Core 216 at 734/1476/1161

Anywhere, here are my settings:

NB Strap (Latch) = 200 (only 200 strap works)
Using 3.33C...

FSB = 300
PCI-E = 101

Vcore = 1.45
VTT = 1.1
PLL = 1.45
My REF voltages are close enough to 60% of VTT that's all i can recall.. +- about .010v

MCH is 1.2, and the rest is stock.

My Memory voltages are 2.080, and the rest of the associated voltages values are half of 2.080 so 1.040.

Memory Timings are set to 5-5-5-15, everything else is auto (As tight as I can get them).

That's probably spot on and it's the best I can recall while I'm here at work.

People always reccomend "LATCH=Auto" which is the same as strap I assume, and ideally that should be setting it to something that I can select manually. The best of my understanding is that it would be 4.00C, which would put my memory at 1200, well above what it can run, so no, it can't run at that. Simple suggestions aren't solving an obviously complicated problem. I tried every strap last night, nothing works but 2.66C at 345 (and below), 3.33C at 300 (and below), and 4.00C at 280~ and below...

I'd like to see something in the 3.9 area with 1120 memory and if I could only get 3.33C working that'd be possible but nooooooo... board and cpu don't like to place nice.

Specifically, does anybody know what I can do to make some of these straps work higher up in the FSB ranges? 3.33C at 300 would be simply amazing and would bring my memory around to where it should be.

Anything I haven't specified is at Auto. Tips, suggestions? Different bios? I'm running out of my own suggestions these days.

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P