Micron D9 GMH\GKX\JKH etc club

[User111]

http://www.memoryc.com/products/desc...kit/index.html
http://www.memoryc.com/computermemor...eemcl3kit.html

the first memory kit has d9gmh? and the second? d9gkx?

[Mafio]

the first memory kit has d9gmh? and the second? d9gkx?

these 2 kits have D9-GMH

[aslanwas]

the first memory kit has d9gmh? and the second? d9gkx?

I got the first one, and i think they have micron D9gmh chips, but mine don't do well, not Cl4 1000MHZ at 2.2V, even not booting, and 1200mhz even not with 2,3V, i think i didn't got the best one, but you can try your luck and get one, but from know on, i prefer only used DDR2 from eBay or anywhere else because they're cheap ( the most expensive one about 30€ ) and if they don't overclock well, you can sell them.
Hope could help you

But
still
go

Team Xtreem

[m0n4g3]

Hi Guys,

I have a set of Corsair Dominator 8500C5D's (2x2gb) v2.2. I've looked at the IC's that are on the set, and all i can gather from the corsair forum is that they are Micron.Gdies.

What IC am i looking at here and what sort of clocks can i expect from them?

I'm reaching 1098mhz on my DFI DK-790FXB-M2RSH with a 940BE at 2.1v. I haven't really tried any other volts as i don't wanna kill em quicker.

Anything after 1098 i get multiple errors in winmemtest but everything else passes perfect!

OCCT Linpac test runs for approx 30 mins before i cancel it and no errors whereas memtest runs less than 2 mins and finds 2 errors.

I can get it posteable until 1200, and it gets into windows perfectly fine, until i run a bench then it dies (i'm actually guessing it's my IMC when this happens as it's running @ 2.75ghz.

Any help with what IC is on these sticks, and possibly with some timing/safe volts/speeds would be awsome!

Thanks guys!

[kuebk]

Theses mems ics aren't microns.

[Ghostleader]

hmmm, here´s from Corsairs forum, the DDR II IC Inquiry.

TWIN2X4096/CM2X2048-8500C5DF
........................XMS850X v1.1...PSC.C-Die.......128MX8
........................XMS850X v1.2...PSC.F-Die.......128MX8
........................XMS850X v2.1...Micron.E-DIE...128MX8
........................XMS850X v2.2...Micron.G-DIE...128MX8
........................XMS850X v3.1...Elpida.C-Die....128MX8
........................XMS850X v3.2...Elpida.F-Die....128MX8

[m0n4g3]

As i said... they are micron g-dies (what ever the hell those are! :P)

I can't seem to get anything out of them! even setting 2.3v @ 1120 i get fails on OCCT linpac.

With the gigabyte board i had them running at 1160 @ 2.35v perfectly fine, just on this dfi board there are subtimings i cannot figure out for the life of me!

if any1 can help me out that'd be great!

Thanks

[zsamz_]

As i said... they are micron g-dies (what ever the hell those are! :P)

I can't seem to get anything out of them! even setting 2.3v @ 1120 i get fails on OCCT linpac.

With the gigabyte board i had them running at 1160 @ 2.35v perfectly fine, just on this dfi board there are subtimings i cannot figure out for the life of me!

if any1 can help me out that'd be great!

Thanks

pumpin 2.35v in rev:G and you think you didnt damage them

[devil_mcry]

Hi Guys,

I have a set of Corsair Dominator 8500C5D's (2x2gb) v2.2. I've looked at the IC's that are on the set, and all i can gather from the corsair forum is that they are Micron.Gdies.

What IC am i looking at here and what sort of clocks can i expect from them?

I'm reaching 1098mhz on my DFI DK-790FXB-M2RSH with a 940BE at 2.1v. I haven't really tried any other volts as i don't wanna kill em quicker.

Anything after 1098 i get multiple errors in winmemtest but everything else passes perfect!

OCCT Linpac test runs for approx 30 mins before i cancel it and no errors whereas memtest runs less than 2 mins and finds 2 errors.

I can get it posteable until 1200, and it gets into windows perfectly fine, until i run a bench then it dies (i'm actually guessing it's my IMC when this happens as it's running @ 2.75ghz.

Any help with what IC is on these sticks, and possibly with some timing/safe volts/speeds would be awsome!

Thanks guys!

but at 1066 is rock solid 100%?
do you have tried with memtest?

[m0n4g3]

ok i figured out what the issue was.

I only pumped 2.35v through them for 5-10 mins to see if they would pass memtest (within less than a min they would error).

The issue was with subtiming (TWR and TWTR being too low).

I used memset to find some of the subtimings from SPD. I'm now able to pass memtest @ 1120 @ 2.2v with 5-5-5-15-4-22-8-4.

Thanks for the help though guys, i'm a much happier now that i can get 12kmb/s copy and 11kmb/s read!

Thanks guys!

What is a safe voltage for a g-die btw?

*Yes at 1066 it passes perfectly fine*

[BeepBeep2]

No more than 2.2v. 2.15v to be safe.

[kuebk]

I have 3 crucial sets
1. tracers 1066 - 600 5-5-5-15 spi32m stable on 2.12v, but can't stabilize them under dos version of memtest even at 2.2v - any clues?
2. tracers 800 - 575 5-5-5-15 memtest stable on 2.2, can't make 600 even at 2.5v,
3. lanfest 800 - can't make 600 even at 2.5v, haven't tested lower frequencies.

Any clues guys?

[aslanwas]

I have 3 crucial sets
1. tracers 1066 - 600 5-5-5-15 spi32m stable on 2.12v, but can't stabilize them under dos version of memtest even at 2.2v - any clues?
2. tracers 800 - 575 5-5-5-15 memtest stable on 2.2, can't make 600 even at 2.5v,
3. lanfest 800 - can't make 600 even at 2.5v, haven't tested lower frequencies.

Any clues guys?

Maybe NO LUCK
Or the rams have a wall there t those frequencies, i've also a kit like this, its working but not Prime Stable even with more than 2.5V

BTW nice ram

[kuebk]

That's what I don't get, how can 3 totally different sets of mem don't oc at least to 600 5-5-5-15.

Haven't got bigger problems with ocing promos to such frequencies but d9 is a nightmare.

[aslanwas]

Lets give us some info about your Board, maybe your board isn't the Overclocker, what about Northbridge Voltage ?

[kuebk]

Rampage Formula as it says in the signature, I've tested up to 1.6v on mch.

[aslanwas]

Does ANYbody of you know, which ICs are under the first generation OCZ Flex XLC Edition CL3



thanks

[Shiranui Gen-An]

Does ANYbody of you know, which ICs are under the first generation OCZ Flex XLC Edition CL3



thanks

Only the 1st Gen DDR2-1150 C5 Flex kits had D9GMH, I remember reading for sure that the 800 C3 kits were not Micron-based.

[sheri]

Tracer Ballistix, Handpicked D9GMH's
How about that? Only 2.1v
What do you think?

[DedEmbryonicCe1]

Nice tRAS.

[aslanwas]

Tracer Ballistix, Handpicked D9GMH's
How about that? Only 2.1v
What do you think?

nice results, keep pushing try 1300 with higher tRas and maybe at 2,25 -2.3V

[Ket]

is Geil GV34GB1600C8DC Micron-based kit?

Thats DDR3 memory........

[stunned_guy]

Found this ones:



Could give voltage up to 3.0 volts under air but it didnt do anything.

[aslanwas]

Very nice rsults on AMD system,

today i got my uses 4*1GB OCZ Flex XLC 1150, on single channel they boot up with 2,8V, but going to take them under cold ( I have to reach the 1600 before dieing :] ).

[aslanwas]

Got some nice Ram from OCZ here, Flex XLC 1150 Cl5,

here some CL4 testing,
Set up:
Q6600
P35 DS4
OCZ Flex XLC 1GB 1150
Excelstore 80GB
Jetway 8800gt
NoName Watercooler
Coolermaster M620
3* Xilence Redwing 1200rpm

here some Validations and Screenshots:

Vaildation @ 1278 Cl4 4-4-4-15 2,8V set, 2,84real

http://valid.canardpc.com/show_oc.php?id=782831

Screenshot 1260 Pi1m