Micron D9 GMH\GKX\JKH etc club

[zen3]

G.Skill PC2-6400 HZ with d9gmh @ 60e.

Shall I buy them? or too much?
The guy that has them now tell me that they can play @ 1000 for 24/7 and @ 1250 for benching.

[zsamz_]

G.Skill PC2-6400 HZ with d9gmh @ 60e.

Shall I buy them? or too much?
The guy that has them now tell me that they can play @ 1000 for 24/7 and @ 1250 for benching.

important thing is voltage used
i rather have d9 that were used 1200+@2.0v-2.04v 5-5-5-15 than d9 used @ 1000 @2.24v 4-4-4-12
i ran most of my d9 1200+ 24/7

[Shiranui Gen-An]

My UT P35 was able to run my newest D9 FlexXLC kit at 555FSB 666MHz C5 PL8.

[kamieldehond]

i found a set cm2x1024-6400c3D G for sale 2.40V ver1.1 has this memory d9gmh chips or d9gkx?

[proxis]

there's no difference between d9gmh and d9gkx

[Shiranui Gen-An]

there's no difference between d9gmh and d9gkx

That's only partially true IMO, as Micron DID bin them differently for a reason. In my experience GKX responds a bit more to voltages than GMH.

[zsamz_]

That's only partially true IMO, as Micron DID bin them differently for a reason. In my experience GKX responds a bit more to voltages than GMH.

yes gkx likes the juice but the more the juice they die quicker

[LennyRhys]

There was a HUGE difference between my GKX and GMH kits - I reckon these particular ICs were binned pretty tight.

I've owned no less than five kits - two GKX and three GMH, all Cell Shock. Both my GKX kits could do 4-3-3-9 at 950MHz with about 2.15v, whereas all three GMH kits struggled to get above 900MHz 4-4-4-10 with 2.1v. The GKX kits did 1100MHz 4-4-4 with relative ease and were also much better with CAS 5 overclocking.

[zsamz_]

There was a HUGE difference between my GKX and GMH kits - I reckon these particular ICs were binned pretty tight.

I've owned no less than five kits - two GKX and three GMH, all Cell Shock. Both my GKX kits could do 4-3-3-9 at 950MHz with about 2.15v, whereas all three GMH kits struggled to get above 900MHz 4-4-4-10 with 2.1v. The GKX kits did 1100MHz 4-4-4 with relative ease and were also much better with CAS 5 overclocking.

most of my gmh did 1300+ n my gkx barely hit 1300 even with 2.8v

[megatron]

i dont get it, my team xtreem 1300s can do 600mhz 5-5-5-15 2.2v orthos stable, doesnt begin to error until 625mhz. yet nothing i do will stabilize it at its rated 650mhz. i have tried 6-6-6-18, pl10, 2.4 vdimm, 1.3 mch quite frankly nothing works using the 5:8 divider as its the only one that will lets them scale to 1200 even.

Not sure about UD3 but I am running 1.36vNb/MCH for P5Q deluxe. 1.28v was unstable with 4 x1 dimm but 1.36v is (didn't test in between).

[chad]

Here is a pair of my Corsair Ballistix PC2-8500 running at 2.28 volts. I have about 1.34 volts on the northbridge. These are 24-7 numbers below. Im weird I rotate between 5-7 kits for these settings. I never had any degradation or a kit burning out. Super Pi results for 1M are 10.5x

[aslanwas]

Corsair Ballistix PC2-8500

[chad]

LOL oops... Just figured it out "Crucial"

[megatron]

1 of my crucial dominators... I mean ballistix has died. I ordered some g.skill pc8800 PI heatspreaders 1.8-1.9v. They were the last kit of its kind in stock. Only need to overclock them 30Mhz to 1130 to test my q9550 at 4Ghz.

I think crucial had a higher failure rate than others using the same chips? I have RMA them and will probably get some crap back. I rma'ed the pair still running on my other pair.

[megatron]

Here is a pair of my Corsair Ballistix PC2-8500 running at 2.28 volts. I have about 1.34 volts on the northbridge. These are 24-7 numbers below. Im weird I rotate between 5-7 kits for these settings. I never had any degradation or a kit burning out. Super Pi results for 1M are 10.5x

[IMG]http://img8.imageshack.us/img8/3683/660memory.png[/MG]

Nice scores and latency, it must be that high value ur using in memset.

[aslanwas]

here some warm-up guys, got 20sticks of corsair dominator, began to test with the best of them, Corsair dominator 10000, 1250 mhz 5-5-5-18

[LennyRhys]

What vdimm you using for 1200 4-4-4 My GKX (when the other module was still functional) needed 2.3v for 1100 4-4-4 benchable.

I didn't realise dominator was D9, but now I see that the PC10000 kits used handpicked GMH ICs which at least explains that they even get to 1200 4-4-4.

Just picked up a 2x1GB kit of Cell Shock 1000 4-4-4 so I'm back in the game (until they die lol ). If I could run 500fsb with DDR 1200 daily I'd be a happy camper.

[Don_Dan]

here some warm-up guys, got 20sticks of corsair dominator, began to test with the best of them, Corsair dominator 10000, 1250 mhz 5-5-5-18

Good work aslanwas, which board are you running?
Can you include MemSet next time please?
Where did you get all these kits?

Just picked up a 2x1GB kit of Cell Shock 1000 4-4-4 so I'm back in the game (until they die lol ). If I could run 500fsb with DDR 1200 daily I'd be a happy camper.

It's good to see some people still pushing DDR2 D9!
I switched to DDR3 currently ( actually, I haven't done anything in the last 3 months ), but I'm sure I will be back to D9GMH/GKX one day, I still have 3 DDR2 kits I never tested...

[Shiranui Gen-An]

here some warm-up guys, got 20sticks of corsair dominator, began to test with the best of them, Corsair dominator 10000, 1250 mhz 5-5-5-18

I miss my kit It could do the same, 600MHz 4-4-4-12 with about 2.45V.

[zsamz_]

I miss my kit It could do the same, 600MHz 4-4-4-12 with about 2.45V.

i miss playin with ddr2
i sold 8 sets last week
but i still got 4 sets on top notch d9

[aslanwas]

What vdimm you using for 1200 4-4-4 My GKX (when the other module was still functional) needed 2.3v for 1100 4-4-4 benchable.

I didn't realise dominator was D9, but now I see that the PC10000 kits used handpicked GMH ICs which at least explains that they even get to 1200 4-4-4.

Just picked up a 2x1GB kit of Cell Shock 1000 4-4-4 so I'm back in the game (until they die lol ). If I could run 500fsb with DDR 1200 daily I'd be a happy camper.

my first D9GKX did 600 CAS4 with 2,6V

Good work aslanwas, which board are you running?
Can you include MemSet next time please?
Where did you get all these kits?

Thx mate, Board P35-DS4, but is going to dy or i am going to kill it (max freq. is about 1400 with these RAM, with a P45, i think i could get over 1600 under cold )

I got these sticks on ebay US, but had to pay over 230€ for all of them, but it was worth as i can see

I miss my kit It could do the same, 600MHz 4-4-4-12 with about 2.45V.

don't worry, be happy

[WaterFlex]

aslanwas
gj

[CryptiK]

Nice results. Haven't busted out my D9 stash in quite sometime.

[chad]

Here is some Buffalo Firestix Pc2-8000 D9GKX. Running 1100 CL4 @ 2.28 volts. Not sure why it is not picking up the proper model in memset.

[chad]

Here is 2x512MB of Team Xtreem Dark Pc2-6400 D9GMH running @ 2.28volts. Im going to try to push these guys, since I don't mind killing a couple 512 chips

FSB 560 1:1 560 4-4-4-12 PL9. Im impressed with the tight timings with PL9