Results 1 to 3 of 3

Thread: IBM Model M Keyboard Fix

  1. #1
    Xtreme Member
    Join Date
    Apr 2006
    Location
    Middle of Nowhere
    Posts
    165

    IBM Model M Keyboard Fix

    The IBM M keyboard is probably the most awesome keyboard every made. You could hit someone upside their head with it and continue typing. Unfortunately, IBM sold the rights for the Model M to Lexmark in 1993 and the quality of the board went downhill. This makes it harder and harder to find replacement parts for it and they eventually break down (albeit after 17 or so years).

    I found this specimen at a rummage sale, the proprietor didn't know if it worked so I got it for $2 USD.



    I took it home and discovered that it did not. If broken, what’s the harm in trying to fix it? First thing I had to do was get it apart. It takes a 7/32" screwdriver to get the screws out.


    After removing the back and front cover I found the source of the problem, the spring board was attached to the metal plate with little plastic studs melted down to disks onto the metal plate. Overtime the disks must have deteriorated and knocked off with all the jostling it got over the years. I numbered all the places where a disk was located and peeled off the rest of the disks. Then I drilled 7/32" holes through the holes in the metal plate into the spring board, careful not to drill through or damage any of the important bits of the circuit sheet or spring board.


    Here is a picture of the circuit sheets. It kept separating so I taped the two sheets together.


    The rubber sheet protecting the circuit sheets form the springs.


    The spring board with springs in it.


    The Buckling Spring.


    When I tried to reassemble it I kept running into a problem, the springs moved from the position they needed to be in and shifted out of place. To counteract this I pressed the springs into the key holders on the plastic spring board.


    I used 10mm long Phillips-head countersunk M3 screws and regular hex nuts to reattach the components together. I found it best to screw it so only half a thread is visible above the hex nut. Any tighter and the keys get squished together and will tend to stick keys together when typing.


    Countersunk screws were used because rounded head ones would push out the metal plate and spring board from the back cover. I couldn't even use countersunk screws on the bottom row (hole 52-59) because of this reason.


    After assembly I flipped the springs back to their original position and attached the keys, testing each one as I went along. I could easily tell if a key wouldn't work if it didn't sound right when I depressed it, but just to make sure I reattached the keys with the keyboard connected to my computer.


    The only thing left was to reattaching the front cover and I was finished. If anyone else would attempted this following this as a guide here are a few things I would do differently.
    + Use 14mm long M2 screws and locking hex nuts.
    + Wash the spring board, front and back covers, and metal plate before reassembly.

    Things I may do in the future to this keyboard
    + replace the circuit board for Native USB support
    + paint the spring plate, and the front/back covers
    + replace the Num, Caps, and Scroll Lock LEDs to better colors (Any suggestions?)
    __________________

    Budgets, Bling, We Need Not These. We Have Science!

  2. #2
    Xtreme Addict
    Join Date
    Jun 2007
    Location
    United States
    Posts
    1,545
    I knew people loved the Model M keyboard, but wow!

    That is pretty amazing, I have to admit. You should definitely continue in this direction, as adding native USB support would be awesome! A cool mod/paint job would probably make me jealous, as everyone lauds this as the greatest keyboard ever created.

    Maybe you could go Xtreme and make some backlit keys or something!
    Sandy Bridge Build:
    • Intel Core i5-2500K at 4.0GHz (Corsair H80)
    • PNY NVIDIA GTX 570 1280MB
    • Mushkin Silverline 8GB (2x4GB) DDR3 1333 RAM
    • OCZ Vertex 60GB & WD Caviar Black 1.5TB HDD
    • 1920x1080 21.5" IPS display (LG IPS226V)
    • MSI P67A-G45 B3 Motherboard
    • Corsair Professional Series HX650W 650W PSU
    • Fractal Design Define R3 (Silver Arrow)

    HP Envy 14:
    • Intel Core i5-450M at 2.4GHz
    • ATI Mobility Radeon 5650 1GB & Intel GMA
    • 4GB (2x2GB) DDR3 1066 RAM
    • Seagate Momentus 500GB 7200RPM HDD
    • 1600x900 14.5" display

  3. #3
    Xtreme Member
    Join Date
    May 2006
    Posts
    271
    I want one of those so bad

    so nice to type on.
    i5-750 Quad Core
    HD 6950 1GB
    MSI P55 GD65
    4GB G.SKILL Trident DDR3
    OCZ GSX 700 PSU
    2* 80GB SATA
    1* 250GB SATA
    HTC Omega Claro+
    Lian Li V2000B

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •