Cooler Master HAF 932

[Anemic]

Im I the only one that thinks it looks kewl? ; ) Looks pretty easy to fit alot of Watercooling gear in it. Might just get one of these cases!

[miptzi]

for me, looks like some super-duper Cm690........

more than enough......... and the price, well, I'd pay.

[Blacky]

probably my next case, too bad it isn't black interior...

[Linchpin]

After looking at a few reviews I have to say I'm coming around as well, just not sure about all the tool-less stuff(can't beat a good old fashioned screw imo).

[axis]

After looking at a few reviews I have to say I'm coming around as well, just not sure about all the tool-less stuff(can't beat a good old fashioned screw imo).

The tooless stuff on the CM690 works very well. Not sure about the 932 but the 690 came with screws for the optical drives if you wanted to secure that way.

Axis

[LuckyNV]

case contents
# Stand-offs 20
# #6-32 screws 40
# M3 screw 30
# M47 screw 16
# Wheel 4
# Cable tie 12
# 5.25” to 3.5” converter shield 1
# Extension cable 1
# Buzzer 1

http://www.motherboards.org/imagevie.../1808_p3_2.jpg

[axis]

(can't beat a good old fashioned screw imo).

I WHOLE HEARTEDLY AGREE.

If the HAF can help with this, I'll buy a couple dozen of em.

Axis

[OdinEidolon]

i relly like that case. the only cons is that it is so big, and i dont think it will fit under my desk .
should i buy a new one (desk of course, i'll buy this case for sure )?

[theodredge]

Stacker 830 is still my best... specially with its side panel modded

[Baron_Davis]

A few things...they say you can fit 3x120mm fans up top, but I only see room for 2...where's the 3rd go?

Second, judging by the specs, the 140mm rear fan can also fit a 120?

Third, you guys think the front 230mm fan is easily removable?

This looks like a sweet case, I wanna try building an "extreme" air cooling case, with 10 Medium speed Slip streams:

4x in side panel
3x up top
1 in rear
2 push/pull for TRUE black
(remove all 230's)

[axis]

A few things...they say you can fit 3x120mm fans up top, but I only see room for 2...where's the 3rd go?

Second, judging by the specs, the 140mm rear fan can also fit a 120?

Third, you guys think the front 230mm fan is easily removable?

This looks like a sweet case, I wanna try building an "extreme" air cooling case, with 10 Medium speed Slip streams:

4x in side panel
3x up top
1 in rear
2 push/pull for TRUE black
(remove all 230's)

Not sure about putting 10x 120's in it but isn't 3x 230s and a 140 pretty extreme to begin with? It's not like they're spinning at 800rpm, they are spinning at 1700rpm. I think they should move a fair amount of air. I have one on order from Directron so I can answer the other questions when it arrives.

Axis

[LuckyNV]

Not sure about putting 10x 120's in it but isn't 3x 230s and a 140 pretty extreme to begin with? It's not like they're spinning at 800rpm, they are spinning at 1700rpm. I think they should move a fair amount of air. I have one on order from Directron so I can answer the other questions when it arrives.

Axis

the 230mm fans are 700rpm and the 140mm is like 1000rpm or 1200rpm

[vengance_01]

Its on newegg 159$ + 30$ shipping.

[Blacky]

http://www.newegg.com/Product/Produc...82E16811119160


!

[axis]

the 230mm fans are 700rpm and the 140mm is like 1000rpm or 1200rpm

You are correct. I looked quickly at the Directron specs and it's a little decieving as its listed like this "230x30mm red LED fan x 1, 700 R.P.M". Guess I should pay closer attention, lol.

Mine has been shipped from Directron so they have them in stock as well.

Axis

[vengance_01]

Cool. It does look like a very solid case to W/C with. Room for a triple rad stock and plenty of ventilation.

[WFO]

Here is a review of the case for those interested.

http://www.planetx64.com/index.php?o...1375&Itemid=14

[axis]

I have mine in hand and must say it's very nice. I'm VERY pleased with it and feel like it is a HELLA deal for $160 shipped to your door.

Axis

[axis]

A few things...they say you can fit 3x120mm fans up top, but I only see room for 2...where's the 3rd go?

Second, judging by the specs, the 140mm rear fan can also fit a 120?

Third, you guys think the front 230mm fan is easily removable?

This looks like a sweet case, I wanna try building an "extreme" air cooling case, with 10 Medium speed Slip streams:

4x in side panel
3x up top
1 in rear
2 push/pull for TRUE black
(remove all 230's)

Now that I have it, I can answer your other questions.

The 3rd top 120mm goes halfway under the cover on the top, you can see the first two holes in the top picture and the other two can be accessed by lifting up the rubber pad. There is a vent in the rear of the cover that exhaust the air from it.

The screws holding the 230s on are a mystery for me or i'm just blind. It doesn't look like a hex and none of my hex bits fit it. I could be a inbetween hex I don't have though. I ended up getting it out with a small square bit I have.

The front 230 can only be replaced by what appears to be single 120. You could probably mod it to take two though.

Axis

[Baron_Davis]

Now that I have it, I can answer your other questions.

The 3rd top 120mm goes halfway under the cover on the top, you can see the first two holes in the top picture and the other two can be accessed by lifting up the rubber pad. There is a vent in the rear of the cover that exhaust the air from it.

The screws holding the 230s on are a mystery for me or i'm just blind. It doesn't look like a hex and none of my hex bits fit it. I could be a inbetween hex I don't have though. I ended up getting it out with a small square bit I have.

The front 230 can only be replaced by what appears to be single 120. You could probably mod it to take two though.

Axis

Excellent, thanks!

[Blacky]

Now that I have it, I can answer your other questions.

The 3rd top 120mm goes halfway under the cover on the top, you can see the first two holes in the top picture and the other two can be accessed by lifting up the rubber pad. There is a vent in the rear of the cover that exhaust the air from it.

The screws holding the 230s on are a mystery for me or i'm just blind. It doesn't look like a hex and none of my hex bits fit it. I could be a inbetween hex I don't have though. I ended up getting it out with a small square bit I have.

The front 230 can only be replaced by what appears to be single 120. You could probably mod it to take two though.

Axis

Hey axis does the case looks complicated to dismount (for inside painting) with all those rivets? I hope not

[gazmtk]

Mines Ordered..... I just dont know when it will arrive, I have 5 Project PC's now.... Tho its a sweet Case!

[axis]

Hey axis does the case looks complicated to dismount (for inside painting) with all those rivets? I hope not

It's not really complicated on the inside. I've never taken one apart but just by looking at it, if you go at it systematically, you shouldn't have a problem.

Axis

[LuckyNV]

How loud, in your opinion, are the 230mm fans?

[Blacky]

It's not really complicated on the inside. I've never taken one apart but just by looking at it, if you go at it systematically, you shouldn't have a problem.

Axis

thanks man