**Unified** DFI LanParty UT 790FX-M2R-M2RS / Phenom /Data Base Thread**

[Final8ty]

That would be a wise idea

Well its hear! AAnnnd its the Exact same stepping as LittleBoy
JAAFB AA 0810APMW

[Oese]

anyone: how about voltages with the 05/05 bios?

gratz @ final8ty

[Final8ty]

anyone: how about voltages with the 05/05 bios?

gratz @ final8ty

Its no guarantee that i will get any ware near LittleBoys cpu but it gives me hope.

[Brother Esau]

anyone: how about voltages with the 05/05 bios?

gratz @ final8ty

Hey, Oli
Tony has taken a DMM Reading of the Vdimm and that has improved drastically and is very close to vdimm set in Bios So making improvements with that finally. I don't have my rig set up on the bench and have asked a couple of times if anyone will be as kind as to get Vcore and NB Voltages with DMM and see how far off that is compared to what is set in Bios but no one has volunteered or people just don't have their board on the bench one or the other.

Do you have you're board on the Bench?

[Brother Esau]

Its no guarantee that i will get any ware near LittleBoys cpu but it gives me hope.

Perhaps you might be as kind as to throw XP64 on you're system and see if you can further validate what I found?

[Oese]

Mmh.. think i'll flash 05/05 and test..

mmh at stock volts (1.4v) dmm is still reading 1.449v..

cpuz reading: 1.424v

[Brother Esau]

Oli , you on 5/5/2008 with that reading?

[Oese]

yepp..

and really, my ram is no longer stable at stock vdimm at those settings, blend priming at stock vcore/2.0v vdimm right now..

[BadNizze]

Two weeks ago I finaly bought a 9850 for my DFI 790, that has been laying in it´s box for abought a month know. Installd win Xp 32bit and flashed to 5/5-08 bios. For me this new B3 is much more stable then my old 9500 and my 9600BE. Been running 2800mhz with brother´s bios template exept v-core wich is 1,28v. Also left the third setting from above starting with vcore @ Auto. BUT, If i leave my rig on over night, it will not come back to life again, will try more vcore... But more voltage heats up my PWM and NB like crazy, PWM was hitting 70C+ before I palced an stock AMD 70mm fan over it, but to make it fitt i hade to remove my Ultra-X and use AMD´s new heatpipe cooler... So now my CPU loads 70C but my PWM stays cool... With my Ultra-X my Cpu loaded 52C... Anyone else have trobble with heat, and how much heat can an Br take 24/7? 55-60c safe?

OCZ VX2 @ 533mhz 1,9v 5-5-5-18
DFI UT 790FX 5/5-08
HD 3870
Corsair HX 520w

Brother Esau, I have a fluke and can problably do some messuring if it´s not to hard, will look into it!

[Final8ty]

Perhaps you might be as kind as to throw XP64 on you're system and see if you can further validate what I found?

Im just to lazy to go trough the hassle

[Oese]

be, seems like with arctic ceramique wlp and 5/5 bios/2,0v vdimm that chip is stable on stock vcore.. but i'll see with rising temps here in summer..

[Final8ty]

I dont understand what the CPU Feature that has snown up in the bois is about?

[flclisgreat]

how does the Ht clock? all ive really seen in here is just raising the multi

[Oese]

@ final8ty: which one? did not see something new...

[Brother Esau]

how does the Ht clock? all ive really seen in here is just raising the multi

HT Oveclocking is Dead and should only be used to dial in the fine tuning of overclock on Phenom. Why does no one get this by now?

[Final8ty]

@ final8ty: which one? did not see something new...

CPU feature shows up in the bios when you run a Quad.

[Oese]

and what does it mean??

[flclisgreat]

HT Oveclocking is Dead and should only be used to dial in the fine tuning of overclock on Phenom. Why does no one get this by now?

because i cant raise the multi on my non phenom cpu? so anyone tried doing 400+ Ht on it?

[Brother Esau]

I said Phenom Oveclocking. Dual Core screams on this board and I had over 360 HT going on with my 6400+BE

[flclisgreat]

I said Phenom Oveclocking. Dual Core screams on this board and I had over 360 HT going on with my 6400+BE

thanks. looking for a board to cook some semprons(low multi).

[Final8ty]

Well my 9850BE was pants & i have gone back to my 6400+BE.
Got my 9850BE upto 2800-2900 but needed 1.6 Vcore and my PSU would shut down if i tried to give it more juice.

The 9850BE would not do more than 2600 on stock Vcore 1.3 & all the cores seemed to be evenly matched when using AOD.

[Brother Esau]

Did you try my settings on the First page?

[Oese]

Well my 9850BE was pants & i have gone back to my 6400+BE.
Got my 9850BE upto 2800-2900 but needed 1.6 Vcore and my PSU would shut down if i tried to give it more juice.

The 9850BE would not do more than 2600 on stock Vcore 1.3 & all the cores seemed to be evenly matched when using AOD.

bad one..

[Brother Esau]

*NEW* 5/5/2008 Official Bios for DFI LanParty UT 790FX-M2R>>>>>http://www.dfi.com.tw/Support/Downlo...FLAG=A&SITE=US

[AlabamaCajun]

Is that off the last beta which I think is 5-5. I have that beta and want to know if I should flash to official? It seems stable as long as I don't OC.

Update;
I put my W5600X2 in the 780M2R to take advantage of running cooler until the 45nms but I encountered hard power off crashes when loaded. I did'nt feel like ing around with it so I put the phenom back in. Problem went away.
What I did observe is that the vcore was at 1.05 when I first booted which meant that CnQ was working. Once I F7ed it and rebooted that feature went away.
How do you get CnQ to work on a Phenom when not OCed?