no problem
no problem
I just recieved my New board from RMA from NewEgg...it's last 4 digits of the serial are 2222, it has the Nichicon caps, and on the version # it was 1.0 on the sticker...but was penned to 1.1. I'll have it up and running soon...as I'm currently working on a review and am using the board as part of it for installation purposes Hope to be blowing some 3Dmark soon my friends
Randi
MrIcee.. I have your boards twin
just hope i get 1/2 the clock you and OPP get from these..
so far im at 2003hz 13.5 X 148..
evrything runs fine except 3dmark2001se.it just locks up b4 the 1st splash screen.been playing cs for the last 2 hours with no problems at all..just wont run 3dmark only tested the 29.42 and the 29.80 dets
im just happy to push this puppy past the 2g mark.
temps have dropped for some reason to 31 idle 45 load.
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
Try this little fix I discovered for locks in 3DMark. You will need to install and set this data with WPCRset:
B0=07
That stopped lockups for me...good luck
Randi
Abit has my board right now, I am waiting for it's return with the fix to put my XP2200+ to work. I will be going through all of your threads for tips to get the best perfomance possible out of it.
Keeper's "Heatware"
Folding for nerdsforjesus.org
ASUS M2N32-SLI DELUXE
AM2 6000
2X36 Gig Rators O/S
2X250Gig Storage
2X 2 Gig Corsair
2X EVGA 7900 GTO
Most people are bothered by those passages in Scripture which they cannot understand. The Scripture which troubles me most is the Scripture I do understand.
-- Mark Twain
MrIcee when i try to set that value to 07 it changes it self to 0F no matter what...This is on Host Bridge Device right ?
Intel i7 3930K C2 @ 4700 mhz (100 x 47) 1.4v
EK Supremacy/EK XTC 420+280/EK DCP4.0/PrimoChill 1/2 ID 3/4 OD
Asus Rampage IV EXTREME
16 GB G.Skill RipjawsZ @ 2400 CL10-12-11-1T
Zotac GTX670
Antec Quattro 850W
Intel 330 180 GB + Micron C400 128 GB
LD Cooling PC-V7 B/R
cheers MrIcee
i allready got Wpcrset install for the hacks to lower my idle temps.
ill give it a try and report back soon..
its 100% stable runnin everything else.
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
MrIcee..the hack didnt work for me..
all i still get when i try to run 3dmark2001se is a black screen,it wont even display the 1st loading screen.
i can press esc and it will exit the prog.so its not lockin up in a way,its just failing to display whats goin on.
the GF4TI4600 is NOT clocked and its set to 4X in bios,side banding is enabled.the only way i can find to diable this,is to use power strip.
the latest via agp driver is installed,even patched XP with the update for the problems with DX8.1 and AMD cpu's.
but still a non runner
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
Im just getting ready for a fresh install of XP..
just backing up stuff from my small hdd..gonna reformat and do a fresh install..
its gonna take some time because i got loads to do over the new few days..
got to go do the airport run to pick up the Outlaws from there hols
ill post my results with the clean install and also with this present install
So far all seems well with the fresh install
even runs 3dmark2001se with no lockups or problems..:smileysex
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
I just got my KX7 in. I can't seem to find a sticker with the revision number. What does it look like and where is it?
EDIT: I found it. I have the same thing MrIcee, v1.0 penned to v1.1. Have you tested it yet with a Tbred?
yeh mine runs sweet
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
Rollin, which version is your board? And which multipliers do you have?
EDIT: Oops, I missed this
In that case, what kind of cooling ar you using?MrIcee.. I have your boards twin
Svenn... my cooling is a globalwin CAK38 copper heatsink.with a delta 7,000 rpm fan on it..
trying to find some where in the UK that stocks the thermalright SK8..
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
Nice, I hope I can get over 2ghz with mine... I'm waiting for my case and rest of my watercooling arrive...
rollin - did you look at the sticker on back of mobo? I know serial number on box is twin but is version same too? look on sticker on back to know. vX.X on right side of sticker.
Svenn..
its back in the case but the sticker had V1.0 with the 0 changed to 1 with a blue biro pen..
ill be popping her back out soon to lap the N/B..
ill write down all the info from the stickers and post all the info..
at the moment im stuck at 2025hz 13.5x150 no matter what settings i try in bios..
think i need to unlock the 2200+ this weekend..just hope i get the time to strip down the system,just got word that the new house is ready
so got a load of things to sort out and do..
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
I have a big problem: with my new 2200+ i can only reach 191mhz fsb when CPU decode is "FAST" and 205mhz at "NORMAL" - with my 1700+ i can get 220mhz (FAST)??
1700+ @217mhz fsb -> http://service.madonion.com/compare?2k1=3873211
2200+ @191mhz fsb ->http://service.madonion.com/compare?2k1=3979481
How can i fix this problem??? Is it a problem between KX7 and Tbred?
Hoschi
Sorry for my bad english - i´m from germany :-)
This is a general trend we have been noticing with each new generation of CPUs. The newer the generation, the less agressive one can set the CPU command decode for higher FSB speeds. I am not sure it is "fixable" at the moment and might be the reason why the Epox 8K31+ does not include the ability to change the value since their 2312 bios for stability.Originally posted by Hoschi
I have a big problem: with my new 2200+ i can only reach 191mhz fsb when CPU decode is "FAST" and 205mhz at "NORMAL" - with my 1700+ i can get 220mhz (FAST)??
1700+ @217mhz fsb -> http://service.madonion.com/compare?2k1=3873211
2200+ @191mhz fsb ->http://service.madonion.com/compare?2k1=3979481
How can i fix this problem??? Is it a problem between KX7 and Tbred?
Hoschi
Sorry for my bad english - i´m from germany :-)
ummm..
thats probly why i keep hitting a brick wall..
just persumed that things would get better and take more aggresive timeings with each new cpu..
XP3200@2530hz..220x11.5..1.850volts..Abit NF7-S V2.0..20 Bios.. 512 TwinMOS pc3700..DangerDen Maze3 cpu block..DangerDen GF4 block..1048 pump..DangerDen Res..Black Ice Xtreme Radiator..165cfm Ystech fan..Zalman N/B HS..GF-FX 5900 Ultra..2x 80g SATA seagate hdd..1x 40g IBM Hdd.1x 60g Maxtor..Plexter 708a DvD-RW..Pionieer 16x DVD..ADSL Router..1meg adsl..Santa Cruz sound card..
Bookmarks