Barton 2500 XP mobile AQZFA 0336XPMW.
2640 MHz at 2.015 volts. (simple watercooling = koolance with zalmanH2Oblock)
Didn't buy it myself swapped it with a locked 2600 Barton .
Barton 2500 XP mobile AQZFA 0336XPMW.
2640 MHz at 2.015 volts. (simple watercooling = koolance with zalmanH2Oblock)
Didn't buy it myself swapped it with a locked 2600 Barton .
Guys, I suggested www.overclockers.com add mobiles to their CPU database. For whatever reason, they have, so I want to see some results!
Please go post your info here (mobiles are last on the AMD list:
http://www.cpudatabase.com/CPUdb/
Thanks, guys.
Current system:
Case: Modded Watercooled Jpac
CPU: Intel Q6600 @ 3.5GHz [1.47v] - OCCT stable
Mobo: DFI LanParty Jr T2RS @ 432fsb [1.37v]
RAM: Crucial Ballistix Tracer 4*1GB DDR2 @ DDR1095 (5-4-5-15) [2.2v]
HD: WD 300GB Velociraptor / WD 640GB Caviar
GPU: HD 4850 Crossfire @ (700 | 2200)
PSU: OCZ ModXstream 780w
I know I am a little bit too late, ~½year or so, but I just trid to run my AQZFA @ 2500+ @ 1.45v , and it is rock stable/prime 95 stable. There maby isn't any huge difference between a xp-m and a regular xp ?
[ Intel Q6600 B3 @ 3.2GHz ][ Asus P5K DLX ][ 4Gb PC6400 ][ X1900XTX ]
Thats coolOriginally posted by oozberg
I know I am a little bit too late, ~½year or so, but I just trid to run my AQZFA @ 2500+ @ 1.45v , and it is rock stable/prime 95 stable. There maby isn't any huge difference between a xp-m and a regular xp ?
Are you running the stock AMD heatsink too ?
EDIT : What temps was it reading ? I bet they were LOW
Last edited by Mickey Padge; 02-22-2004 at 01:29 PM.
No I got a crappy Vulcano 7+, but it is better than a stock hfs anyway...
My temp are "that" good, but far from bad, currently ~34ºC, load ~40ºC
[ Intel Q6600 B3 @ 3.2GHz ][ Asus P5K DLX ][ 4Gb PC6400 ][ X1900XTX ]
They are about the same temps I get with my mobile 2400 @ 2700mhz with 2.0v vcore
I am using a vapochill though
Heres what i got with my IQYFA 0343 MPMW Mobile Barton
2100+ T-bred @2.4ghz at 1.8 vcore
Abit NF7-S Rev2.0
2x256mb of twinmos Pc3200
9700 pro @440/380 *dead*
9700 pro @410/375 *dead*
3DMark03
3DMark01se
My heatware
temps in the range of 30°C+? must be something wrong then, try reseating the cooling head!Originally posted by Mickey Padge
They are about the same temps I get with my mobile 2400 @ 2700mhz with 2.0v vcore
I am using a vapochill though
hehe
Thats the socket diode not the CPU diode temp .
CPU diode under prime load averages 0c and the evap reads -14c more or less .
Thats with the compressor working at 60% too .
If I up the compressor to 100% it gives no more OC , but lowers the average temp a bit . I will have to do the vcore mod to push this CPU more .
I hear the mobiles can get quite a kick in speed when you give them over 2.0v , I just have not got around to doing it yet
240x12
|
|
V
sig
Pc Power and Cooling SILENCER® 750W
Q6600 (kentsfield) @ 3870
asus p5k-e
Gskill 800 @ 1032
bfg 8800gt
Creative SB XFI plat
interesting.. the IQYFA look like the god chips. my IQYHA and your AQYFA are only one letter off but clock very well. wonder if we'll ever know wtf the stepping means? lol
it looks as though the F being an H is worse than the I being an A. im not sure if my chip can hang at 2.5gig with 1.8v
Dell Studio XPS16... no desktop
yes i have AIM, yes you can send me a message. EvilSpork3 i dare you.
Fantastic resultOriginally posted by Cow2kie
240x12
|
|
V
sig
What CPU stepping and cooling though ?
Cheers
AXMH 2500 FQQ4C
K028535A40095
IQYFA0343MPMW
Using a prommy for cooling. I could prob push it more except i need more than 2v on this dfi
Pc Power and Cooling SILENCER® 750W
Q6600 (kentsfield) @ 3870
asus p5k-e
Gskill 800 @ 1032
bfg 8800gt
Creative SB XFI plat
I can get plenty on the continent, picking up the 1st one wednesday.
AXMH2500FQQ4C
K028535A40113
IQYFA0343MPMW
Just started playing so I can't claim the right of full stability but so far it's looking good.
Currently priming, 2 hours and counting at 2.8 (13x215.5) 1.94v 39c water cooled on an NF7-S rev 2.
Very, very nice.
E6600 @ 3.6ghz - Tuniq Tower / Asus P5B Deluxe / 2gb G-Skill HZ/ ATI 3870 / Silverstone OP650
im ordering one this weekend for sure.. these are too good to pass up.
E4300|IB9|Ultra-120 Extreme
My 2500+ is doing 2400MHz (12 . 200) @ 1.7v with rather high ambient temps and a brand new application of AS5.
It did 11x200 @ 1.6 rock stable, probably less but I never tested it.
IQZFA 349 RPMW in case anyone was wondering.
Proud Founder of Redline 3D
Just got my mobile today. Similar steping to this. IQYFA0343MPMW. I think its week 0340 tho. I was too excited to check but i will after burn in. Was able to get 2 gigs at 1.5 with a temp of 30C all air in a warm room. Lettin it burn in overnite with 1.9v going in it. Hopefully its like MediOCre's and Hallowed's but ill keep ya posted.
Cheers!
Small update: Requires 1.73v actual (1.725 in BIOS).
Prime is good, 3DMark and UT2k4 passed.
Wonderful chip!
Proud Founder of Redline 3D
not too shabby!! lets see some max speeds soon! i just love these chips! its hard not to buy my third!
Dell Studio XPS16... no desktop
yes i have AIM, yes you can send me a message. EvilSpork3 i dare you.
2460 is good for browsing so far @ 1.73. Ambient dropped 10 degrees though (70F now).Originally posted by Evil_Spork
not too shabby!! lets see some max speeds soon! i just love these chips! its hard not to buy my third!
Just slowly inching up the chip at low volts, fav method of burn-in.
I am truly impressed with this chip so far.
Proud Founder of Redline 3D
i did that with mine.. set it at 1.8v, then just jacked up the speed.
ended up at around 2675 with 1.8v and it lasted for a while in windows. i think it might have even run sandra!
Dell Studio XPS16... no desktop
yes i have AIM, yes you can send me a message. EvilSpork3 i dare you.
What cooling? SLK900A and a 43CFM 80mm here, decently quiet setup.Originally posted by Evil_Spork
i did that with mine.. set it at 1.8v, then just jacked up the speed.
ended up at around 2675 with 1.8v and it lasted for a while in windows. i think it might have even run sandra!
edit: 2500MHz @ 1.78v now, browsing about.
Proud Founder of Redline 3D
Bookmarks