my E8500 has a 1.165V VID and can hit 4.7ghz on water with 1.66v (in bios) 1.625V (real)
my E8500 has a 1.165V VID and can hit 4.7ghz on water with 1.66v (in bios) 1.625V (real)
what did you use for the real?
I run my memory at 2.1V 5-5-5-15. I tried it at 4-4-4-12, but I ran into a lot of blue screens, so I loosened the timings.
I run about 40 idle and under load I hit as high as 68. I need to remove my heatsink and lap the IHS on the proc and the heatsink. Should give me a performance boost with regard to heat.
------------------------------------------------------
Main Rig
PSU - Corsair TX750W
Board DFI LP LT x48 T2R
CPU - E8400 4.0 Ghz 9 x 445
Cooling - AC Freezer 7 - 36 idle 58 under load
Mem - 2X Corsair XMS2 2GB DDR2-800 (OC to 890)
OS -Vista Home Premium X64/Ubuntu8.04
GPU - VisionTek 900241 Radeon HD 4850 512MB
HDD - 2X Western Digital Caviar SE16 640GB 7200 RPM RAID 0
Case - Antec 900
i think my e8500 is no good.. this sucks.. ill bet this is why i had code 88's on the other 2 dfi mobo's.. this sucks
upgrading...cooler master cm690 case, corsair hx850, samsung 1tb x 3, optiarc burners x2, gskill 4gb ripjaws, working on the rest again
Last edited by Arbitr; 07-15-2008 at 07:13 PM. Reason: hooked on phonics
e8400 @ 4005MHz (1.26v) EP35-DS3L
Corsair XMS2 DDR2 800 @ 890
ECS 8800 GTS (G92) 512mb
Seagate 7200.11 500gb
------------------------------------------------------
Main Rig
PSU - Corsair TX750W
Board DFI LP LT x48 T2R
CPU - E8400 4.0 Ghz 9 x 445
Cooling - AC Freezer 7 - 36 idle 58 under load
Mem - 2X Corsair XMS2 2GB DDR2-800 (OC to 890)
OS -Vista Home Premium X64/Ubuntu8.04
GPU - VisionTek 900241 Radeon HD 4850 512MB
HDD - 2X Western Digital Caviar SE16 640GB 7200 RPM RAID 0
Case - Antec 900
Xclio A380 | E8600 4.5GHZ | Swiftech MCP665 | Black Ice GTX 360 & Magicool 360 Xtreme | D-tek FuZion V2 | Asus Striker II Formula | 2x2 G.Skill 1200mhz | 2x WD 250GB, WD 500GB | GTX 260 SLI with EK WB | Corsair HX750| Samsung 245B+ | Logitech G15 | Logitech Z-5500 | X-FI Elite Pro | Logitech G25 | Razer DB@QcK+ | Xbox Wireless Controller|
http://www.mygarage.ro/pc-tuning-mod...tercooled.html
theoretically yes you can... to "lap" and IHS ... you just take sandpaper and flatten your IHS and the CPU heatsink ... sometimes you get a concave/convex CPU cooler or CPU IHS ... and when you "lap" them it flattens them all all out for better contact ... "and theoretically lower temps".... temps will very greatly from this though.
i have seen temps drop like 10-15C to the other extreme of actually going up a couple C .... so lap at your own risk ...
hmmm...ok...the IHS is the surface of the CPU or what?...i got the point...i must flat the cpu to get better contact...my cooler ZALMAN 9700CNPS is verry flat and nice...the cpu seems to be the problem...
I have another problem...OCCT and CoreTemp shows me +10 degres more then RealTemp...for exemple in RealTemp i have right now 46c idle, cooler high, and in OCCT, CoreTemp i have 56 ...and OCCT has a limit 70c max to run the test...i must set the value to 80c...what is the real temp ?...WTF?...i think the real temp is 46 because the cooler is cold...under load the cooler is still cold...theoretically at the wrong temp that OCCT and CoreTemp indicates (74-76c), the cooler itself it's hot...but it is't...
Last edited by So3oL4Nu; 07-16-2008 at 01:08 AM.
Xclio A380 | E8600 4.5GHZ | Swiftech MCP665 | Black Ice GTX 360 & Magicool 360 Xtreme | D-tek FuZion V2 | Asus Striker II Formula | 2x2 G.Skill 1200mhz | 2x WD 250GB, WD 500GB | GTX 260 SLI with EK WB | Corsair HX750| Samsung 245B+ | Logitech G15 | Logitech Z-5500 | X-FI Elite Pro | Logitech G25 | Razer DB@QcK+ | Xbox Wireless Controller|
http://www.mygarage.ro/pc-tuning-mod...tercooled.html
Core2Duo E8400 SLAPL Q743A689 BX80570E8400 DICE @ 5.22ghz 8.875 SuperPI 1M
DFI Lan Party UT P35 T2R - DEAD NOW - Overbaking isnt working
Crucial Ballistix Tracers DDR2 1066 kit
Core i7 Sandy Bridge 2600K @ 4.3ghz
MSI P67A-GD80 (B3)
Kingstons 8gig kit DDR3 1600 T1's
Xonar D2X Sound Card
Inno3D 470GTX 1.5gig
Antec Trio True Power 650watt
Samsung T260 LCD
Logitech z5500's Surround Sound
Kingston 128gig SSDNOWV100 series
Sammsung 1x 1TB drives, Seagate 500 SATA2
Asetek Watercooling Custom
Custom Wooden case
Realtemp is correct as it's based on TJcasemax 95 while OCCT and Coretemp still use 105 as value, so they are 10°C off... you can adjust coretemp Tjcasemax via options - settings and putting in -10 in the Tjunction Max offset box.. for OCCT only thing to do is to put like you did put 80 instead of 70 there
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro Asus Saaya yupp, I agree
Last edited by So3oL4Nu; 07-16-2008 at 04:14 AM.
Xclio A380 | E8600 4.5GHZ | Swiftech MCP665 | Black Ice GTX 360 & Magicool 360 Xtreme | D-tek FuZion V2 | Asus Striker II Formula | 2x2 G.Skill 1200mhz | 2x WD 250GB, WD 500GB | GTX 260 SLI with EK WB | Corsair HX750| Samsung 245B+ | Logitech G15 | Logitech Z-5500 | X-FI Elite Pro | Logitech G25 | Razer DB@QcK+ | Xbox Wireless Controller|
http://www.mygarage.ro/pc-tuning-mod...tercooled.html
zzz
Last edited by AriciU; 07-24-2008 at 04:38 AM.
Intel i7 920 d0 @ 4410MHz @ 1.36v :: Prolimatech Mega Shadow :: Gigabyte EX58-UD5 F9K :: 6GB Mushkin XP3-15000 :: HIS 5870 :: Corsair 1000W :: HannsG 27.5" :: Lian Li V1010B
We have roughly the same temps. Before lapping, I suggest running load with your case open and a fan blowing into it You could lower temps more than 5c if you have poor case ventilation. I added a stronger rear exhaust fan and organized cables better, with around 5c improvements.
EDIT: if you are still concerned..... I feel 100% safe if load temps typically stay around 65c an lower, system temps 60c and lower. There is no reason to feel these are dangerous temps.
I never break 60c when playing crysis.... and Prime and Folding keep it sub 60c with spikes in the low 60s now and then
Last edited by Arbitr; 07-16-2008 at 04:35 AM.
e8400 @ 4005MHz (1.26v) EP35-DS3L
Corsair XMS2 DDR2 800 @ 890
ECS 8800 GTS (G92) 512mb
Seagate 7200.11 500gb
Are you using this ram --> http://www.newegg.com/Product/Produc...82E16820145184
1.9v is the requirement
e8400 @ 4005MHz (1.26v) EP35-DS3L
Corsair XMS2 DDR2 800 @ 890
ECS 8800 GTS (G92) 512mb
Seagate 7200.11 500gb
Xclio A380 | E8600 4.5GHZ | Swiftech MCP665 | Black Ice GTX 360 & Magicool 360 Xtreme | D-tek FuZion V2 | Asus Striker II Formula | 2x2 G.Skill 1200mhz | 2x WD 250GB, WD 500GB | GTX 260 SLI with EK WB | Corsair HX750| Samsung 245B+ | Logitech G15 | Logitech Z-5500 | X-FI Elite Pro | Logitech G25 | Razer DB@QcK+ | Xbox Wireless Controller|
http://www.mygarage.ro/pc-tuning-mod...tercooled.html
Leeghoofd and friends - I want to get an E8500 to play with after the upcoming price drop , is there a particular batch I should watch for ?
Last edited by aussie-revhead; 07-16-2008 at 05:46 AM.
Bencher/Gamer(1) 4930K - Asus R4E - 2x R9 290x - G.skill Pi 2200c7 or Team 2400LV 4x4GB - EK Supreme HF - SR1-420 - Qnix 2560x1440
Netbox AMD 5600K - Gigabyte mitx - Aten DVI/USB/120Hz KVM
PB 1xTitan=16453(3D11), 1xGTX680=13343(3D11), 1x GTX580=8733(3D11)38000(3D06) 1x7970=12059(3D11)40000(vantage)395k(AM3) Folding for team 24
AUSTRALIAN DRAG RACING http://www.youtube.com/watch?v=OFsbfEIy3Yw
AFAIK 8500 batch # Q807 like my xeon are good.
SB Rig:
| CPU: 2600K (L040B313T) | Cooling: H100 with 2x AP29 | Motherboard: Asrock P67 Extreme4 Gen3
| RAM: 8GB Corsair Vengeance 1866 | Video: MSI gtx570 TF III
| SSD: Crucial M4 128GB fw009 | HDDs: 2x GP 2TB, 2x Samsung F4 2TB
| Audio: Cantatis Overture & Denon D7000 headphones | Case: Lian-Li T60 bench table
| PSU: Seasonic X650 | Display: Samsung 2693HM 25,5"
| OS: Windows7 Ultimate x64 SP1
+Fanless Music Rig: | E5200 @0.9V
+General surfing PC on sale | E8400 @4Ghz
Nope. I use this ram --> http://www.newegg.com/Product/Produc...82E16820145194
------------------------------------------------------
Main Rig
PSU - Corsair TX750W
Board DFI LP LT x48 T2R
CPU - E8400 4.0 Ghz 9 x 445
Cooling - AC Freezer 7 - 36 idle 58 under load
Mem - 2X Corsair XMS2 2GB DDR2-800 (OC to 890)
OS -Vista Home Premium X64/Ubuntu8.04
GPU - VisionTek 900241 Radeon HD 4850 512MB
HDD - 2X Western Digital Caviar SE16 640GB 7200 RPM RAID 0
Case - Antec 900
Btw, Leeg. I was wondering how one goes about getting on the OC list?
------------------------------------------------------
Main Rig
PSU - Corsair TX750W
Board DFI LP LT x48 T2R
CPU - E8400 4.0 Ghz 9 x 445
Cooling - AC Freezer 7 - 36 idle 58 under load
Mem - 2X Corsair XMS2 2GB DDR2-800 (OC to 890)
OS -Vista Home Premium X64/Ubuntu8.04
GPU - VisionTek 900241 Radeon HD 4850 512MB
HDD - 2X Western Digital Caviar SE16 640GB 7200 RPM RAID 0
Case - Antec 900
sweeeeeeet ... my dominators are coming today ... they better work with my board
then i can finally OC my e8400
E8400 Q15A @ 8.5x500=4250Mhz with 1.28 vcore -- TRUE 120 with Scythe Ultra Kaze in push pull
ASUS P5Q Deluxe 1702 Bios -- PC Power & Cooling Silencer QUAD Crossfire 750w
2x1GB Crucial Ballistix PC6400 (16FD5) & 2x1GB Crucial Ballistix PC8500 (16FD5) @ 1000mhz 4-4-4-12 PL9 @ 2.17v real with Corsair Dominator Active Cooling
ATI HD4870x2 Cat 9.1 - Custom modded ASUS TOP Bios 832/1000
2 x Samsung F1 1TB + 1 x Samsung F1 320GB -- X-Fi Xtreme Music -- Logitech G15 v2 + Razer Lachesis
Dual Boot XP 32 SP2 + Vista 64 Ultimate SP1 -- Samsung T220 22" Monitor (Samsung Panel) + Samsung LEA656 40" 1080p TV
Got hands on E8500, batch Q814A678 Batch. Passed 12 hours of Prime on 9.5x400 (3.8 GHz) at 1.224V. Did pencil mode on my motherboard, but for hitting 4 GHz (9.5x425 - 4.037 GHz) needs much nore voltage. Currently testing at 1.376V under load, 1.38750V in BIOS. If it passes, can I use this for 24/7 work? Also if it passes, I'll try with lower volatages.
CPU: E8500 @ 3.825 GHZ @ 1.304V (pencil mod) ; Cooler: ZEROtherm Nirvana NV120 Premium ; Mainboard: EVGA nForce 750i FTW CPU FSB @ 1.200V nForce SPP @ 1.400V NF200 @ 1.200V ; Memory: 2x1 GB OCZ XTC nVidia Ready SLI DDR II 900 MHz @ 2.100V 4-4-4-12 ; GPU: ZOTAC GeForce 8800 GTS 512 MB @ 760/1860/1080 PSU: Tagan 430W Modular Chasis: CoolerMaster CM690
Bookmarks