c2d 4200 only 33 degree

[AuriL]

I setup again my water cooled rig
and the results are impressive

E6850 3000 @ 4200 mhz
vcore 1,55
ambient : 23 degree

idle just 33 degree
full load under orthos ( 2 core enable ) 66 degree ( usable 7/24 )

[weirkved]

I setup again my water cooled rig
and the results are impressive

E6850 3000 @ 4200 mhz
vcore 1,55
ambient : 23 degree

idle just 33 degree
full load under orthos ( 2 core enable ) 66 degree ( usable 7/24 )

let me see orthos running

[AuriL]

no prob

just give me a little time

I want to run a spi 32m

after that u can get what u want

[AuriL]

uh sorry mate
I could'nt get any temp readings @ 1,55 vcore cause it's not stable enough to run orthos

I could get that
@ 1,6 vcore idle




and 1,6 vcore load under orthos ( cause of the extra 0,05 vcore is the difference of 66 - 73 degree , thanx )

[KTE]

Your chip should be cool looking at the VID, but what does your chip do in temps at stock idle, any pics?
Looking at that, your hardware sensors looked borked because your 36C at 4.2GHz/1.61V after 5 min torture would mean you're getting sub-16C idle at 3GHz/1.28V in 23C ambient.

Can you give us EVEREST showing temps and Core Temps along with it at any speed/volts (idle)?

[AuriL]

Your chip should be cool looking at the VID, but what does your chip do in temps at stock idle, any pics?
Looking at that, your hardware sensors looked borked because your 36C at 4.2GHz/1.61V after 5 min torture would mean you're getting sub-16C idle at 3GHz/1.28V in 23C ambient.

Can you give us EVEREST showing temps and Core Temps along with it at any speed/volts (idle)?

sorry
where u get that - 16 degree ????

[KTE]

What temps does you chip idle at stock volts 3GHz? Any pics?

[jimmyz]

thermal measurement is 15c off the t-junction should be 85c not 100c therefore 15c lower than actual, in other words addd 15c to your temps. it is a common issue ,sorry to disappoint you.

[AuriL]

What temps does you chip idle at stock volts 3GHz? Any pics?

here is the def

[systemviper]

thermal measurement is 15c off the t-junction should be 85c not 100c therefore 15c lower than actual, in other words addd 15c to your temps. it is a common issue ,sorry to disappoint you.

how can you tell its should be 85 not 100 from those screens/images

[AuriL]

how can you tell its should be 85 not 100 from those screens/images

what I know is absolutely the versus of that

when tjuncion is 85 it must 15 degree below of my measure not above

feel free to correct me

edit : I mean when u measure with tjuncion 85 u have 15 above what I measure

[jimmyz]

common problem been known about for months. for instance my phase unit is at -41 yet core temperature is reading -50 in everest, cpuz, etc. with 1.6v going to my cpu it is obvious that the temps are off.

[jimmyz]

what I know is absolutely the versus of that

when tjuncion is 85 it must 15 degree below of my measure not above

feel free to correct me

edit : I mean when u measure with tjuncion 85 u have 15 above what I measure

exactly that means instead of 33 you are at 48c which is still only as accurate as the software it is using anyway.

[AuriL]

edit : I mean when u measure with tjuncion 85 u have 15 above what I measure

please anyone can confirm us with the readings and g0 rev. will be appreciated


ps : I know my english is crappy , so u all wellcome

[AuriL]

@jimmyz


so can u give me any prog ( exclude speed fan it freezes my system )

so I can give you whatever you want

[jimmyz]

nothing to do just add 15c when you look at the temps. I use the same board with an e-6600 and the temps read 15 degrees colder than they should be. for instance my asus p5k deluxe read 4 degrees c warmer than my evap temp. where the p-35 lp-ut reads 11 degrees colder than the evap. which is impossible.

[AuriL]

hmm

you r talking about e6600 and there is differences with my go rev e6850

and what I know theres 15c difference with the ex models of conroe

I'm talking about g0 rev's
so please give me any temp reading prog , we can compare our results
or I can compare with your program and coretemp (tjunction 100 )

thanks for your help

[KTE]

thermal measurement is 15c off the t-junction should be 85c not 100c therefore 15c lower than actual, in other words addd 15c to your temps. it is a common issue ,sorry to disappoint you.

I think you're muddled up there jimmy.
E6x50 (G0) have Tjunction of 100C, E6600 and others before then had Tjunction of 85C. You can see this with my last C2D, E6750 with 85C Tjunction idling 1.48V BIOS 3.72GHz ambient 14C:



As you can see, it should be TJunction 100C, so +15C to those temps.

[AuriL]

lol

that's what I want to mean

thanx a lot @KTE

[jimmyz]

I think you're muddled up there jimmy.
E6x50 (G0) have Tjunction of 100C, E6600 and others before then had Tjunction of 85C. You can see this with my last C2D, E6750 with 85C Tjunction idling 1.48V BIOS 3.72GHz ambient 14C:



As you can see, it should be TJunction 100C, so +15C to those temps.

i guess what i am saying is the same you add 15c to the temps it gives you to get actual temp. it is just that I run on the - side since i am sub-zero.

[KTE]

I understand, but AuriL your temps are still very... unexplainable though.

[AuriL]

I understand, but AuriL your temps are still very... unexplainable though.

lol

Auril

apogee gt blok
mcp 655 pump
360 nexoss hc rad
1/2 barbs
2 x ystech 135 cfm fan
1 x fm121 110 cfm fan

ambient temp : 23
cpu idle: 32-33