Ok just to say i have not done any measurements for hell of a long time so wait for verification from someone else if the readings sound about right, but if they are way off then well i suck at taking readings
DMM setting = 200
For both points measured against pin #13 on the pic i got
0.3
I done it a couple of times at it hovered on 0.7 but it eventually went to 0.3 both points
DMM setting = 20k
Also K404 i did a measurement on Pin#13 FB and Pin#4 AGND got a reading of
5.12k
Last edited by Rumon; 11-29-2007 at 06:06 PM.
I can confirm the same readings as Rumon
#13 + Middle point = .3
#13 + Right point = .3
Resistor that is in-between Middle + Right point = 5.1k ohm
Im guessing the value doesn't change between the middle vs right point is because it only goes through the bottom of that resistor in its path.
And a quick measure of
#13 + #4 = 5.1k
I'm using a cheap Radioshack DMM, but its close enough that we are getting the same readings
Last edited by Miwo; 11-29-2007 at 06:57 PM.
'Gaming' AMD FX-6300 @ 4.5GHz | Asus M5A97 | 16GB DDR3 2133MHz | GTX760 2GB + Antec Kuhler620 mod | Crucial m4 64GB + WD Blue 2x1TB Str
'HTPC' AMD A8-3820 @ 3.5GHz | Biostar TA75A+ | 4GB DDR3 | Momentus XT 500GB | Radeon 7950 3GB
'Twitch' AMD 720BE @ 3.5GHz | Gigabyte GA-78LMT-S2P | 4GB DDR3 | Avermedia Game Broadcaster
Desktop Audio: Optical Out > Matrix mini DAC > Virtue Audio ONE.2 > Tannoy Reveal Monitors + Energy Encore 8 Sub
HTPC: Optoma HD131XE Projector + Yamaha RX-V463 + 3.2 Speaker Setup
vGPU mod (untested):
edited out
Last edited by largon; 11-30-2007 at 07:47 AM.
You were not supposed to see this.
Weird. The measuring point should work...
The square pads are on the same plane as vGPU chokes' outputs.
You were not supposed to see this.
Using a guide on VR-Zone..I was gonna suggest a 100K pot from Pin 13 to ground.
OR a point connected to the FB pin, if it makes soldering easier.
Again....theory, and untested.
INVALID INFO
->
*edited out*
Last edited by largon; 11-30-2007 at 07:46 AM.
You were not supposed to see this.
Both Rumon and Miwo got a FB-GND resistance of 5.1K, not 5.1 ohm...or is there a mass mis-communication going on?
Guide on VR-Zone says use a pot of 20x the resistive value of FB pin to GND. Im not pulling numbers out my ass, or making this up as I go along
I admit...taking general 2nd hand info isnt the ideal approach though...
___________________
I agree with the readpoints though
5.1kΩ?
Wowza! You're right!
:O
edit:
Yup.
100kΩ VR would be good.
Last edited by largon; 11-30-2007 at 08:03 AM.
You were not supposed to see this.
It's works well! I use a 100K VR between one green point and the ground, actually testing 1.5v vgpu for 975mhz...
i7 3960X@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC19200C8, Corsair force GT 240go, 2XGTX Titan, MM Ascension, Seasonic X-serie Gold 1250W, Watercooling
i7 3930K@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC17000C9, OCZ Vertex 3 120go, GTX670 DCU2 Top, MM Pinnacle, Corsair AX850, Watercooling
Excellent seeing as largons green markers include the FB pin, il take that as confirmation it works.
Il update the first post.
Please can you try some resistor values for the RAM mod as well, and we can get that locked down too?
K
i7 3960X@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC19200C8, Corsair force GT 240go, 2XGTX Titan, MM Ascension, Seasonic X-serie Gold 1250W, Watercooling
i7 3930K@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC17000C9, OCZ Vertex 3 120go, GTX670 DCU2 Top, MM Pinnacle, Corsair AX850, Watercooling
K404 i didn't test the ram now, my goal is to find some log where i can clock both cards i own (stupid limit in overdrive to 885mhz)
i7 3960X@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC19200C8, Corsair force GT 240go, 2XGTX Titan, MM Ascension, Seasonic X-serie Gold 1250W, Watercooling
i7 3930K@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC17000C9, OCZ Vertex 3 120go, GTX670 DCU2 Top, MM Pinnacle, Corsair AX850, Watercooling
Congrats pinto, and thanks for sharing.
Have you added any relevant info about BIOS flashing to the other thread in the 3D section- it looks like you got past the PLL divider fine!?
excellent
hope my soldering skills are up to the job, those points are pretty damn small
What resistance did you set the 100k VR to obtain 1.5vcore? Are you getting any black screens that would be a hint at OVP ?
Next is a vmem mod, hopefully those gddr4 chips scale well
'Gaming' AMD FX-6300 @ 4.5GHz | Asus M5A97 | 16GB DDR3 2133MHz | GTX760 2GB + Antec Kuhler620 mod | Crucial m4 64GB + WD Blue 2x1TB Str
'HTPC' AMD A8-3820 @ 3.5GHz | Biostar TA75A+ | 4GB DDR3 | Momentus XT 500GB | Radeon 7950 3GB
'Twitch' AMD 720BE @ 3.5GHz | Gigabyte GA-78LMT-S2P | 4GB DDR3 | Avermedia Game Broadcaster
Desktop Audio: Optical Out > Matrix mini DAC > Virtue Audio ONE.2 > Tannoy Reveal Monitors + Energy Encore 8 Sub
HTPC: Optoma HD131XE Projector + Yamaha RX-V463 + 3.2 Speaker Setup
Some optional solder points marked in green:
Attachment 68027
Last edited by largon; 01-12-2008 at 12:35 PM.
You were not supposed to see this.
It's time for a: 1GHz GPU clock
The RAM mod is provisonally done as well, but we need someone to try: 100K, 50K, 20K etc pots until theres an increase in VGDDR at max resistance.. sorry- I cant be more precise. If you start at 100K though, the card is unlikely to be damaged
well could we get crysis benchmark test @
1280 pixel
4x aa
high details
in win xp
pinto if you could take an actual pic of your mod that would be great, thanks! I just want to double-check before I go about soldering
'Gaming' AMD FX-6300 @ 4.5GHz | Asus M5A97 | 16GB DDR3 2133MHz | GTX760 2GB + Antec Kuhler620 mod | Crucial m4 64GB + WD Blue 2x1TB Str
'HTPC' AMD A8-3820 @ 3.5GHz | Biostar TA75A+ | 4GB DDR3 | Momentus XT 500GB | Radeon 7950 3GB
'Twitch' AMD 720BE @ 3.5GHz | Gigabyte GA-78LMT-S2P | 4GB DDR3 | Avermedia Game Broadcaster
Desktop Audio: Optical Out > Matrix mini DAC > Virtue Audio ONE.2 > Tannoy Reveal Monitors + Energy Encore 8 Sub
HTPC: Optoma HD131XE Projector + Yamaha RX-V463 + 3.2 Speaker Setup
i7 3960X@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC19200C8, Corsair force GT 240go, 2XGTX Titan, MM Ascension, Seasonic X-serie Gold 1250W, Watercooling
i7 3930K@5ghz, Asus Rampage IV Extreme, 8gb Gskill RipjawsZ PC17000C9, OCZ Vertex 3 120go, GTX670 DCU2 Top, MM Pinnacle, Corsair AX850, Watercooling
never volt modded a card before but i'd be willing to do it on these... could do with a simplified guide if at all possible.... ordered duorb coolers ready for the mod...
Bookmarks