QX9650+DRAGON F1 first attempt: 7.921SPI 1M

[nachthymnen]

A really difficult day today
A lot of humidity, yesterday night never stop to rain
Lost a lot of time with my GX2 for nothing.
Many times the vga disabled 1 of the 2 gpu and the 3d score are terrible.
Also I've made a really week insulation and the mobo in around 30minutes was completly frozen
The Dragon need a really strong insulation
After many hours I was able to test a little bit the Dragon and is simply amazing
I've bench 3d'03 and '05 without problems @ 5.7Ghz 1,91v
But cause of bad insulations mobo goes crazy
Unfortunately I've also kill 1 of my 2 GB of CS 14400
So, a really bad day, I'm happy for the POT, is awesome.
Next time with a Foxconn X48+my 9800GTX TEK9 cooled I hope to do something's good


SETUP:
MVE LAB 30
Dimastech bench table
QX9650 L739A664(CB @ -143)
Dragon F1 EE
Asus P5E3 WS PRO
1GB CellShock 14400
Club 3d 9800GX2
Sirtec High Power 1200W
Win Xp+Sp3












Some screens, nothing special

A really low score in a testing '06 run


CPU Testing through 3d '05:


And this is the screen that save the day
SPI 1M @ 5847Mhz=7.921


No Eram and No Max Mem used, only realtime SPI.

[redratamd]

Good job guy
About your 05 . It was with 9800GX2 ?

[nachthymnen]

Good job guy
About your 05 . It was with 9800GX2 ?

Tks
Yes, with 9800GX2 non oced and only 1GB of RAM.
As I say, a lot of time the vga in OC disable 1 gpu and the score sucks
I've do a 3d'03 @ 5.7Ghz with vga @ 752/1121/1901 but only 62.7k
Not saved the screen.
Really frustrating to bench under LN2 with this card

[R@ptor =]]]

Good job mate!!
7.9 second on pi 1mb??
you kill 1 of 2 gb ...but the cause it's temperature?
how much voltage you are using on the memos??

[Solarfall]

how are you liking that asus P5E3 WS PRO board nachthy ... i really need to get a good ddr3 board

[c1rcu1tburn3r]

Good job ma friend!!!

[nachthymnen]

Good job mate!!
7.9 second on pi 1mb??
you kill 1 of 2 gb ...but the cause it's temperature?
how much voltage you are using on the memos??

I don't know the really cause of my stick of ram's dead
Only 2.12V when she dead

In the SPI shot I've set 2.2V to the survived stick

@Solarfall:
Hey, this board is really good my friend
Super stablility on the voltages and no cold boot problems

@ Circuit:
Tks my friend.
Now I need a board that give me mouch v-core
I won't risk an OVP on this, I've only this CPU

[Yeknom]

Good job with the nice sPi! Pretty good CPU there.

[nachthymnen]

Good job with the nice sPi! Pretty good CPU there.

Tks
The SPI can be lower and lower @ this frequencies but I'm happy of the result

[R@ptor =]]]

Hum...very strange the memo die like that
i'm using 2.1 in my tracers @ 800mhz 4-4-4-12...2.1 it's much voltage (2.1v) without any air cooler on the memos?
i think i can put a lower voltage, but later i gonna try, i want to buy a p5k premium

[nachthymnen]

Hum...very strange the memo die like that
i'm using 2.1 in my tracers @ 800mhz 4-4-4-12...2.1 it's much voltage (2.1v) without any air cooler on the memos?
i think i can put a lower voltage, but later i gonna try, i want to buy a p5k premium

Yes
Well' you have DDR2, but I know that many people do over 2.3v on DDR3 also.
Maybe tomorrow is possible that all works fine again, not 100% sure that the stick is dead but is more than possible

[xwards]

nice benching

[R@ptor =]]]

But i don't know if 2.1v in my memos it's much....I'm afraid to kill them with this voltage..i'm using this voltage without any air cooler on the memos..
In your opinion, 2.1v in ddr2 like that memos it's much without any air cooler??

[Gautam]

Nice chip you got there for sure.

[nachthymnen]

Nice chip you got there for sure.

Tks Gutam
This is my only CPU, dayly use also from september 2k7
The chip can go higher but he want more volts and my P5E3 with this cpu over 1.92 is really unstable, impossible to bench
I'm already searching for a BlackOps

[c1rcu1tburn3r]

@ Circuit:
Tks my friend.
Now I need a board that give me mouch v-core
I won't risk an OVP on this, I've only this CPU

You can do a controlled ovp with a trimmer and fixed resistor

[andre X_X]

Nicely done ... nice pi1m result too...

[surrealX]

Nice job.

[DMH]

But i don't know if 2.1v in my memos it's much....I'm afraid to kill them with this voltage..i'm using this voltage without any air cooler on the memos..
In your opinion, 2.1v in ddr2 like that memos it's much without any air cooler??

No,2,1V in DDR2 is cold even for none air cooling,in DDR3 2,1V it's the equivalent to 2,4V in DDR2

[Oliver]

Good to see u got your f1ee tested and looks good, sweet chip ...

Sad about the gx2 card... do u have more information about this, when did u see core disabling on the card?...

Keep pushing it.

[SF3D]

Core slowdown (disabling SLI) is the cold bug on these GX2 cards. Don't take that card over ~-45c and you should be ok. At least my card behaves that way.

Good cpu you got there

[pippo369]

Great job Giorgio, your pot is very strong. You can try a new Asus P5E 64 Evolution for more Vcore.

[Nulpunt]

Nice chip you got there,

i've benched the black ops yesterday i can tell you its a hole other world,
Bios feature's are amazing,but i had bad luck had a diffcult cold bug
Hope you'r run will be beter

[n3wbi3]

Nice going mate
Shame about ur CS stick

[nachthymnen]

@ All: Tks guys
The Dragon is really amazing, no other words for describe it.
Just I must take more confidence with him, is extremely reactive

@Sf3d: Tks friend
Well, my GX2 was on stock cooler
I've this problem also with cpu on air.
Sometimes, I don't know when and why she disable 1 gpu
Maybe a bios problem?
Other people have my same problem

@Pippo: Tks
Waiting for Foxconn Blackops when I'll be able to find it