*Official Retail G0 Q6600 Overclocking Thread*

[mascaras]

can any one tell me why i am get deff temp

thats what i´ve suspected , maybe peedfan its the right one , with C2D E4300 its same thing , speedfan reads low temps than coretemp




Dazog download Speefan and try it out

speedfan >> http://www.almico.com/speedfan.php

[ruff97]

are you say speedfan is the right temp becuase if it is i am going to push it more

[Xilikon]

Xilikon, what is your max OC so far?

Didn't try for max yet, just installed mine 1 hour ago and currently doing some baseline checks (temps and stability at stock voltage). I will try tonight for max or tomorrow and will report back...

[Dazog]

speedfan reports much lower temps.

[Supertim0r]

I think you'll be limited to 3.5ish with the xbx2

[Termite617]

ncix upped the prices after the initial cut on the Canadian site, due to low supply or something.

Same thing probably happened on the US site, it was 260 and then bumped back up. Right now its on sale for $1.50 off the regular price so it was probably alot lower before.

http://forum.ncix.com/forums/index.p...oduct_id=22211

[Xilikon]

I think you'll be limited to 3.5ish with the xbx2

Why are you saying this ?

I ran my E4300 to 3.6 (9x400) fine so I know I may be able to reach the same ballpark...

[mascaras]

are you should speedfan is the right temp becuase if it is i am going to push it more

are you using watercooling????


your temps are pretty good even in Coretemp , 3500mhz = 45c Idle ( coretemp )

speedfan reports much lower temps.

how much ???

and coretemp 0.94 , did you try it???

[Supertim0r]

Why are you saying this ?

I ran my E4300 to 3.6 (9x400) fine so I know I may be able to reach the same ballpark...

max fsb with a quad core on XBX2 is 395ish

[Dazog]

are you using watercooling????


your temps are pretty good even in Coretemp , 3500mhz = 45c Idle ( coretemp )





how much ???

and coretemp 0.94 , did you try it???

Speedfan reports temperatures 15c cooler than coretemp

[mascaras]

Speedfan reports temperatures 15c cooler than coretemp

so 70c FULL @ 3200mhz @ Watercooled ????

i think its also too high temp , maybe its the waterblock >>
http://www.xtremesystems.org/forums/...ght=storm+quad


anyway check if the storm its correctly mounted

are you should speedfan is the right temp becuase if it is i am going to push it more

3500mhz -- 45C Idle (coretemp) its really good , are you using watercooling????


regards

[XtremeTiramisu]

I think Speedfan 4.32 is reporting the correct temp.
I think what everyone fails to see is that the Tjunction is 100c for the Q6600.

Coretemp 0.95 isn't reporting the temp the way we interpret it.

Simple math substraction gives me that the 4 core temp reading form coretemp 0.95 - 15c = speedfan 4.32 core temp readings.

A little background on the accuracy of core temp readings from speedfan 4.32:

Take my E6700 for example (please see my sig)
When I was using Vista 32bit, I could opened up coretemp 0.95, Intel TAT and Speedfan 4.32 to check to see if all temp reading were reading the same. The result is they're all reporting the temp the same with only 1~2c off difference.

When I swithced to Vista 64bit, I cannot longer use the Coretemp 0.94/95 and Intel TAT becouse the softwares aren't written to support the Vista x64 but I could still use Speedfan 4.32 and the temp is still reading exactly the same as before on Vista 32bit but a few degrees cooler becouse the AC MX-1 paste has settled in.

I remember reading somewhere else Speedfan actually reads the Tjunction properly and takes it into account than Coretemp does. Speedfan basically acts exactly the same as coretemp becouse they all can read the temp from the diodode so the accuracy is the same but speedfan takes Tjunection into account so in the end watever the readings from Speedfan4.32 should be accurate.


I'll first lap my Thermalright Ultra120 Extreme becouse it's very convex and after I get everything setup I'll also post my temp/OC results.

It's good thing that all three of us have the exact same batch L723A765 - Dazog, Xilikon and I.

We should have almost identical OC / temp readings. If Dazog temp is off by that much, that means the fault must lies somwhere else and not the CPU itself. Xilikon's temp is already diff than Dazog but the same batch. I'll give in my result later tonight....

[Dazog]

Yea i will have to pick up a new block.

Looks like the storm can't handle the 4 cores.

[ruff97]

are you using watercooling????


your temps are pretty good even in Coretemp , 3500mhz = 45c Idle ( coretemp )





how much ???

and coretemp 0.94 , did you try it???

Yes i am watercool. it is in my rig

[mascaras]

Yes i am watercool. it is in my rig

nice temps and nice CPU


regards

[heydo6]

Did you do Canada or USA?

usa ...if you pm me your invoice or post it i'll ask for the difference in price . wish i could have seen them at $260 i would have got a couple . maybe i should call them

[ruff97]

here temp at full load

[ruff97]

can any one tell me how to run ORTHOS for all 4 core it is just run it for two of the core

[lowfat]

I think the fact that he uses a Storm is the biggest reason of the poor temps. Storms are poor on LGA775, nevertheless quad core where the jets are barely even hitting the CPU dies. If you went to a Fuzion your temps would decreases drastically.

[virtualrain]

can any one tell me how to run ORTHOS for all 4 core it is just run it for two of the core

Prime 25.3

[mascaras]

can any one tell me how to run ORTHOS for all 4 core it is just run it for two of the core

check in task manager if CPU usage its 100%


regards

[ruff97]

Prime 25.3

then is what i am use Prime 25.3, but i think ORTHOS can eun on all core too

[I)ickie]

Lets see some more results guys!
Just sourced a place that will ship me a g0 here in Australia so curious to see how they go!

[ruff97]

check in task manager if CPU usage its 100%


regards

just two of the core are being test

[Forsaken1]

just two of the core are being test

Run two instances then set the affinity of the 2nd program to use core 3 and 4