air cooled E6850 week23 4100mhz->Pi32m, 4ghz->prime95 :)

[PcCI2iminal]

the good news



1.6v

1.58v


3600mhz @ 1.3v

max screen at 1.65v

http://valid.x86-secret.com/show_oc.php?id=219533

and the bad news
FSB wall ->500FSB

i will give some cold

CPU->E6850 L723A
MB->Gigabyte P35-DS4
Cooler->Thermalright Ultra 120 eXtreme
Fan->San Ace F12-PWM
RAM->A-data 8500 EE
PSU->Giga-EZ 1000w
Room temp->26C

[StyM]

nice..

[safan80]

nice.. so what's you 1M superpi time?

[rithina]

Very new cpu. ouch..sad to hear wall is at 500 fsb...but 3.6 at 1.3v is excellent for 24/7 for most of u

[Cordovader]

Very nice PcCI2iminal

It´s curious because my E6850 E0 does almost literally the same on air with an Ultra Extreme too:

Max validation at same vcore


Almost the same Spi 32m (23mhz more)


And same stability, 3,6ghz 1,3v


It´s nice to see that the retail one´s are so good too

[Endre]

Excellent results by both of you! I've just ordered a similar system to the OP, a E6850, DS3P (DS4 with less cooling), and some cheap Ballistix 5300. Can't wait when I see these results. The 6850 seems like a better choice than 6750 if you wanna have a "guarantee" to reach frequencies at least close to 4G stable with highend air or lowend water.

A shame with the FSB wall, I'm glad I didn't order a lower MP chip.

[HamidFULL]

very nice ... and idle and load temp??

[ceevee]

Great news. E6850 should be here as well in a couple days.

I'm trying some new stuff with this build, went with a DDR3 only board and going to try a TEC cooler for the CPU.

Looking to get 3.8-4.0Ghz 24/7

[PcCI2iminal]

Very nice PcCI2iminal

It´s curious because my E6850 E0 does almost literally the same on air with an Ultra Extreme too:

hehehehe

nicely done mate

what fan are you using?

very nice ... and idle and load temp??

I really don`t know ,the CoreTemp does not report the temps right with this cpu
idle < room temp :S
but the Thermalright`s base is not hot @ 4ghz

A shame with the FSB wall, I'm glad I didn't order a lower MP chip.

Unforunately the chip FSB walled @ 500 fsb on air(6x,7x,8x)

but it`s time to break some walls

[eva2000]

Nice... but shame about the FSB wall

nearly everyone of my cpus is walled at 490-514FSB on water cooling LOL

bought a 2nd hand E6600 L709A958 to play with hope it has a higher FSB wall

[PcCI2iminal]

eva2000

i want a 600FSB+ chip
and good luck with your "new" E66

nice.. so what's you 1M superpi time?

I'll try that. It may take a day to re-run them all

[PcCI2iminal]

and a bit more for screen hehehe
http://valid.x86-secret.com/show_oc.php?id=219654

no more than 534FSB (6x,7x,8x)

cooling->dice
vcore->1.74v

[Dynasty]

nice work with the e6850......

[eva2000]

eva2000

i want a 600FSB+ chip
and good luck with your "new" E66



I'll try that. It may take a day to re-run them all

thanks

looks like you managed to squeeze a bit more out 534FSB is decent and 4.7ghz is nothing to complain about

what's the max on DI @~1.66v vcore ??

[over@locker886]

Great chip my friend!

But low fsb wall is little sad..

[PcCI2iminal]

here George



1.65 Bios
1.62v real

looks like you managed to squeeze a bit more out 534FSB is decent and 4.7ghz is nothing to complain about

you are rite ,nothing to complain ,I`m very happy with my new 4ghz Conroe

Bit of a Dilema.
put this cpu in my main machine
or keep my quad @ 3400mhz :S

[over@locker886]

here George

you are rite ,nothing to complain ,I`m very happy with my new 4ghz Conroe

Bit of a Dilema.
put this cpu in my main machine
or keep my quad @ 3400mhz :S

I vote about 4Ghz Conroe

[Solarfall]

excellent numbers brotha.. what about 3Dmarks

[kiwi]

Great on air/water and maybe phase but rather sad for xtreme cooling and benching Such chips would do at least 5Ghz on DICE if not fsb wall

Thanks for info

[PcCI2iminal]

RD600 + Intel cooler box(QX6700)




3.78GHZ was all I could get and the E6850 works fine on 1222 Bios

Room temp @ 24C

[luihed]

Great on air/water and maybe phase but rather sad for xtreme cooling and benching Such chips would do at least 5Ghz on DICE if not fsb wall

Thanks for info

It is a great cpu for aircooling but thats about it.... all I can say is this is not what you want if you like superpi cos its soooooo slllooowwww......

@3600mhz ( 514x 7 )

E6600= 13m11s
E6850= 13m39s

Mine is L722a and on water itll do 4300mhz+ and fsb@ 545fsb.... good numbers but my E6600 can do the same..... kinda dissapointing

[nugzo]

It is a great cpu for aircooling but thats about it.... all I can say is this is not what you want if you like superpi cos its soooooo slllooowwww......

@3600mhz ( 514x 7 )

E6600= 13m11s
E6850= 13m39s

Mine is L722a and on water itll do 4300mhz+ and fsb@ 545fsb.... good numbers but my E6600 can do the same..... kinda dissapointing

I wouldn't be disapointed. You have a very special E6600 if it does 4.3. I just ordered a 6850 from the egg. be here tuesday. My goal has been 4ghz 24/7 on good water. I've been able to make it to 3.9 on my 10th E6600. Maybe this 6850 will finally get me there.

[zsamz_]

i doubt if many e6850 wont reach 4.0
never got to test with my p35 board died as soon as i put it in lol
but my old p5b got it to 4.0 stable on first try with my zalman
my 120 extreme came in 30c load

[erwinz]

It is a great cpu for aircooling but thats about it.... all I can say is this is not what you want if you like superpi cos its soooooo slllooowwww......

@3600mhz ( 514x 7 )

E6600= 13m11s
E6850= 13m39s

Mine is L722a and on water itll do 4300mhz+ and fsb@ 545fsb.... good numbers but my E6600 can do the same..... kinda dissapointing

so you got an E6850..

wow so 1333 cpu's are slow in pi..

[Cordovader]

hehehehe

nicely done mate

what fan are you using?

The retail fan that comes with the Tuniq tower

My cpu tops out on air at 538fsb +/- But days ago i did a little test with LN2 (the board, unmoded, hanged and i had to stop early) and it changed

1m 5133mhz 1,68v




Right now i´m priming at 3,2ghz 1,19v, 20m so far

Greetings