With the 1226v bios, vanderpool is enabled but grayed and will not give an option of disabling it.
Would you know why this is happening?
Should it matter much if I let it enabled since I'm not running virtuals?
With the 1226v bios, vanderpool is enabled but grayed and will not give an option of disabling it.
Would you know why this is happening?
Should it matter much if I let it enabled since I'm not running virtuals?
i7 920 D0 4GHz | Rampage II extreme | Dominators 3x2Gb 1600MHz | Asus GTX580
Corsair AX850 | Haf-X and W/C | postville 80GB | Dell u2412m | Win7 ult SP1
---
Q6600 G0 3,2GHz | Asus P5B deluxe | ZALMAN 9700 LED| Adata 2x2 +Supertalent 2x1 GB |
Gigabyte GTX285 | CHIEFTEC CFT-560A | 690 II adv | Samsung LE40F86BD| Win7 ult SP1
~ Play and enjoy, you might die tomorrow ~
That's normal actually. You can only enable/disable it from a cold boot. I don't think leaving it off will affect you in any way. I believe it's only there if needed but I could be mistaken.... why don't you run virtuals? They are the ultimate tool for testing new/unknown software before hosing your "main" system.
Microsoft virtual PC 2007 is freeware now, just google it. You can make a fresh XP or Vista or etc. install to a virtual HD and then save that file to always has a fresh system image for testing purposes.
Thanx for the tip.Maybe I'll give MS vPC a try.
By cold boot, you mean booting after restoring factory defaults in bios?
---
I noticed you added the E8000 series in the Intel offerings list.
I recently purchased an intel E8200 and wanted to warn E8000 series owners about temps that are reported by coretemp or speedfan regarding these cpus.
These utilities can't be trusted on the 45nm series.
Just for reference I originally had mine at stock cooling and no tower fans.
Coretemp reported 55C idle/ 65C prime25 load.
After installing a scythe mugen cooler and 4 tower fans, coretemp still reports 55C idle but 58C prime25 load.
I came across this theory http://www.xtremesystems.org/forums/...d.php?t=179044 that might give a logical explanation as to why this is happening.
Just wanted to share the link so that other newbies like me don't panic on their first coretemp reporting as I did.
Cheers.
i7 920 D0 4GHz | Rampage II extreme | Dominators 3x2Gb 1600MHz | Asus GTX580
Corsair AX850 | Haf-X and W/C | postville 80GB | Dell u2412m | Win7 ult SP1
---
Q6600 G0 3,2GHz | Asus P5B deluxe | ZALMAN 9700 LED| Adata 2x2 +Supertalent 2x1 GB |
Gigabyte GTX285 | CHIEFTEC CFT-560A | 690 II adv | Samsung LE40F86BD| Win7 ult SP1
~ Play and enjoy, you might die tomorrow ~
Thanx for the tip, I finally disabled it.
After numerous tries to achieve 8*400, I never got it stable at max vcore 1,1265v.
Not wanting to go higher on voltage, I gave the exact given in this topic configuration for the cpu, but running 4:5 833 MHz the memory @4-4-4-8 2.1v. (I'm still to stop thinking like thatabout the 6400 sticks)
I get an error in prime25 in about 2hours n 20 minutes.
I just did the vdroop mod and am running a smallfft's test with prime, waiting for the results. If I get an error again I'll loosen memory timings and ratio before giving any more voltage.
I'll post again when I finally get a stable system.
As far as you know, could it be the memory that's causing the errors? I mean since I'm running the smallfft's test that doesn't test memory as prime25 says.
i7 920 D0 4GHz | Rampage II extreme | Dominators 3x2Gb 1600MHz | Asus GTX580
Corsair AX850 | Haf-X and W/C | postville 80GB | Dell u2412m | Win7 ult SP1
---
Q6600 G0 3,2GHz | Asus P5B deluxe | ZALMAN 9700 LED| Adata 2x2 +Supertalent 2x1 GB |
Gigabyte GTX285 | CHIEFTEC CFT-560A | 690 II adv | Samsung LE40F86BD| Win7 ult SP1
~ Play and enjoy, you might die tomorrow ~
Could be the memory, but it's tough to say... it could also be one of your MB vcores is a touch too low... 1.1265 V @ 8x400 is VERY LOW! My B3 Q6600 needs 1.3375 V to boot @ 8x400 and +1 level on the NB and +1 on the FSB term. voltages. I dunno if that's p95 stable or not. 9x333 is fast enough for me on this system.
Sorry for the typo, I meant to write 1,2625v but it's still far to low from the 1.3375 voltage you used.
Anyway also sorry for not being clear, what I meant by "the exact given in this topic configuration for the cpu" is that I'm now running @ 9*333 @1,2625v as you. All other voltages are one click up from auto too.
With this configuration and the memories in the quoted sync, I get the prime25 errors.
Btw I'm now at 2hours & 33 minutes stable. Maybe the vdroop mod was all I needed.
I pray it lasts for 6 hours![]()
i7 920 D0 4GHz | Rampage II extreme | Dominators 3x2Gb 1600MHz | Asus GTX580
Corsair AX850 | Haf-X and W/C | postville 80GB | Dell u2412m | Win7 ult SP1
---
Q6600 G0 3,2GHz | Asus P5B deluxe | ZALMAN 9700 LED| Adata 2x2 +Supertalent 2x1 GB |
Gigabyte GTX285 | CHIEFTEC CFT-560A | 690 II adv | Samsung LE40F86BD| Win7 ult SP1
~ Play and enjoy, you might die tomorrow ~
succinct guide, well done.
i7 3610QM 1.2-3.2GHz
OK, just got finished upgrading the guide to version 1.6!
• Added a detailed section to help you find the minimum stable CPU and MB vcore settings. Check it out (near the bottom of the guide entitled, “Stress Testing and Minimizing Your Vcores”)!
• Updated the CPU table
• Provided a less than $5 method you can use to shave off some NB load temps (in the thermal management section at the end of the guide).
Any chance you could add a section on GTLref voltages? I havent seen much if any info on them...especially like max GTLref votlages etc.
Therein lies the problem... I don't feel comfortable writing about GTL's since I don't have a good handle of them, and what might happen to your system long-term if you use values that are above the rumored 67 % of VTT that is the default. As I said in the guide:Originally Posted by graysky
graysky, this guide is great, one of the best guides I have read. One suggestion, you provide an example where random cores fail and you diagnose/fix the problem. Could you post some other common issues that encountered when OCing Intels. For example, what if the same core keeps failing, which most of us know is most likely a weak core and the CPU may need more voltage. Thanks and great work again.
CURRENT RIG
Q6600 2.4 GHZ @ 1.45V
2X 2GB MUSHKIN Redline @ 550 MHZ[5-5-5-12]
TRUE W/ PUSH/PULL YATE LOONS
EVGA 8800GT
ASUS P5K-E
COOLERMASTER CM-690
SEASONIC 500W
I agree a fictitious log is not the way to go, but you could post some common Intel OCing issues and tips to resolve them.
CURRENT RIG
Q6600 2.4 GHZ @ 1.45V
2X 2GB MUSHKIN Redline @ 550 MHZ[5-5-5-12]
TRUE W/ PUSH/PULL YATE LOONS
EVGA 8800GT
ASUS P5K-E
COOLERMASTER CM-690
SEASONIC 500W
nice guide gray , was a brave move
regards
c2d e8500 q822a536
x38-t2r LT bios 10/2
ocz blade 9200 2x 2Gb
4890 sapphire catalyst 9.7
3x samsung spinpoint p120 250Gb 2xraid0 stripe 16k
pioneer dvr216
850w silverstone st85f
akasa omega
swift storm
swift mcw-30
1x 240mm thermochill & 1x 120mm rads
mcp-655 pump
dell 2407wfp
windows xp pro x64
I'm an Intel overclocking noob and would very much like to have the guide on paper so I could read and tweak at the same time. I think it's a great guide btw!
ASUS P5Q DELUXE
Intel Q9450
Mushkin 4GB
Asus GTX260
^^ Print it! ^^
First post was unclear indeed. What I meant was graysky to make a pdf or doc
or whatever to people to print. I would like to print it indeed but didn't want to
start copying and making it nicer looking. I'm lazy I know it...the first overclocking manual I read was from the dfi-street and they had it as a pdf.
If it was too much to ask I'll make one myself then. Just thought it would be great to be able to print it without a hassle.
ASUS P5Q DELUXE
Intel Q9450
Mushkin 4GB
Asus GTX260
hereya go... easy enough...
1MB PDF http://scootplace.net/fah/C2DOC.pdf
Last edited by MikeB12; 08-14-2008 at 01:55 PM.
Just found this guide while searching for something, just had to read it, very good guide and very well written.
Dave. Unofficial, rambling and sometimes useful comments
QX9770
Foxconn BlackOps
Corsair Twin3X4096-1600C7DHXIN G
EVGA GeForce 9800 GX2 SSC
Thermalright Ultra 120 eXtreme with Push/Pull Noctua NF-P12 fan
Enermax Galaxy 1000W
WD VelociRaptor 300GB
Case - Zalman Z-Machine GT1000
Monitor - Dell 24"
Currently Vista Ultimate x64 SP1
Awesome guidereally helpful for a noob like myself
Intel Q6600 G0 3.0GHz
Intel DX38BT 1333MHz
Corsair DDR3 1333MHz 9-9-9-24 4x1GB
Visiontek ATI Raedon HD 4870 512 MB 790MHZ/1100MHz
Acer AL2216W
Bookmarks