ASUS P5K Deluxe Vmods.

[Pete]

Bah, no one then able to help and conferm which work

[SF3D]

What is your problem? If you look first post, you can see all other mods but the vdroop. I have tested all of them and they are working for sure.

Working vdroop mod is posted in earlier page.

I hope this is enough for you, or is there something else that you want to know exactly?

(This thread could be renamed to ASUS P5K-E / Deluxe / Premium Vmods.)

[Pete]

Go and read through the topic, people saying it work it doesn't. I want full confermation to which does and doesn't work

[largon]

Go and read through the topic, people saying it work it doesn't. I want full confermation to which does and doesn't work

What are you talking about?
I've re-read the thread now twice and can't find a single post complaining non-working mods.

I HAVE TESTED THESE MODS AND THEY ARE WORKING 100%.[/SIZE]

Pete,
Here's all the confirmation you need...

[The Stilt]

I suggest you measure the PLL VCC voltage from smd caps under socket instead of the fet under dram slots.

The difference between these spots is over 0.3V.

Also when modifying any CPU related voltage, you should keep the wires as short as possible.
Thats because the regulators kick out alot of noise and the cpu is very sensitive to it.
Wires that long will work as antennas and they might do more harm than gain in overclock.

Of course this is the case with all of the mods.

If these mods don´t work, it´s just you

[pablopawel]

What totals Vdroop in P5K-E??

Does not have that VCore measure point??

Sorry- my English is no good.

[harleybro]

Wires that long will work as antennas and they might do more harm than gain in overclock.

Thanks for the tip. I am on my third P5K and brought the mod all the way to the bottom of the board this time but none of my OC's where even close to what they had been when the mod was up top. That might explain it since I was clueless.

[LivingL@rGe81]

Hey guys

I've done the Vdroop mod on my P5K Deluxe & it works great

Set in bios at 1.6125V I get 1.608V Idle & 1.60V load which is perfect for me

Been looking around the board & noticed that the R27 coils around the CPU socket burn my fingers straight away! Is there any point in putting heatsinks on them?

Where is the PLL chip on these things?

[sobol]

Hi there folks
I have strange instability with P5K Deluxe. Please help.

I've performed vdroop pencil mod. The voltages went up and they're almost identical to what is set in the bios. The damper is enabled.

Now overclocking Q6600 to 3.6 with 1.45v give me full stability, but not quite. It can do Small FFT stable for 8 h and then another run next day will fair after few hours. On top of that some games just hangs.
I've observed small fluctuations of cpu vcore during load times.

Perhaps lead layer isn't conducting properly, maybe it's to thin, or depending of the temperature? ( fluctuations of ambient temp. )
Now I've made over theory, but I'm not sure if it's right?

[itslogz]

So does this mod deffinetly work for the P5K-E? Just the pencil mod part?



Could I just do the pencil mod part and see any results?

[BNDMOD]

Hey someone can post all readpoint for this mobo?
I'd like to do a panel with all coneccion for read vcore, vdimm, nb, sb all as posible :d

[bl1zZ]

Where to SOLDER vdroop mod?
Which resistors do I need?

Best Regards
Dennis

[Counter CS]

Where to SOLDER vdroop mod?
Which resistors do I need?

Best Regards
Dennis

You don´t need to solder nothing.
Just use a pencil 4B to the yelow mark
I have done it on mine.

BIOS : 1.400v
BIOS monitor: 1.416v

WIndows idle: 1.408v
Windows load: 1.400v

http://www.xtremesystems.org/forums/...1&d=1188759155

[Rock&Roll]

I had to roll back to the 0602 BIOS in order to get rid of Vdroop. The pencil mod helped a little bit for me, but the BIOS put everything where it should be. I havn't tried the latest 0803 bios yet. My board came with 0703.

[Counter CS]

I had to roll back to the 0602 BIOS in order to get rid of Vdroop. The pencil mod helped a little bit for me, but the BIOS put everything where it should be. I havn't tried the latest 0803 bios yet. My board came with 0703.

BIOS 803 ???

you wanted to say that the board came with 603, and you haven't the latest 703

[KeyzerComponent]

sweet

[pablopawel]

Hello!

I need VFSB{FSB Termination} to P5K Dlx and measure point.

[nFo]

What is: Vsb ??

[pablopawel]

VSB= V South Bridge. I need VFSB{FSB Termination}

[BarboneNet]

You can use 50Kom in parallel the resulting resistance should be around 25Kom, according to my calculations (original resistance is ~48Kom).

Best Regards.

Vdroop mod with solder VR 50kohm in parallel WORK FINE

now i have this vdroop on my P5K-E:
Bios 1,360v
Idle 1,368v
Load 1,360v

[proxis]

anyone with GTL ref Vmod guide for these mobos?

(looks like it's needed with 45nm chips)

[KumKum]

hi all

its my second P5K Premium Black Pearl Edition and for the second time the Vcore CPU MOD does not function and give anything...

What is the pb, im alone to known this pb on P5K Premium Black Pearl ??

[LittleDevil]

Where is the closest ground point on vcore mod?



Regards

[KumKum]

yes no pb, i do that since more years

I found the problem
it was the trimmer 50k which I use since severals months on my differents MOBOs

I assembled a new and that functions now

thanks


ps : Congrats for yours SS !! I see one to a member of a forum in France ---> Nice and good job guy

[Felipe]

sf3d thx!