Need stability help! Core i5 650!

[nolonger]

I've been trying to get my system stable at the following settings:

Bios Version:
*Frequency/Voltage Control*
Dummy O.C : Disabled
Target CPU Frequency : 4080MHz (170x24)
Target Memory Frequency : 1700MHz (2:10)
CPU Multiplier Setting : 24x
CPU Frequency Setting : 170MHz
PCIE Frequency Setting : 104MHz
QPI Frequency Selection : 6400 GT/sec
MCH Strap : Auto
Extreme Cooling : Disabled
EVGA VDroop Control : Without vDroop
Current CPU Vcore : 1.35V
Bootup CPU Vcore : Auto
Eventual CPU Vcore : 1.35V
Current Dimm Voltage : 1.68V
DIMM Voltage : 1.68V
Current VTT : 1.4V
Bootup CPU VTT : Auto
Eventual CPU VTT : 1.4V
Current PCH Voltage : 1.2V
PCH : 1.2V
Current CPU PLL : 1.8V
CPU PLL : 1.8V
DIMM 1/2 DQ Vref : Auto
DIMM 3/4 DQ Vref : Auto
DIMM 1/2 CA Vref : Auto
DIMM 3/4 CA Vref : Auto
CPU PWM Frequency : Auto
VTT PWM Frequency : Auto
DDR PWM Frequency : Auto
CPU Signal 1 : Auto
CPU Signal 3 : Auto
CPU Signal 4 : Auto
CPU PCIE 1 : Auto
CPU PCIE 2 : Auto
DDR Signal 1 : Auto
DDR Signal 2 : Auto
DDR Signal 3 : Auto
DMI Signal : Auto
PCH Signal : Auto
*Memory Configure*
IMC Type : Clarkdale
DRAM SPD : Standard
DRAM Frequency : 1333MHz
Target Memory Frequency : 1700MHz
DRAM tCL : 9
DRAM tRCD : 9
DRAM tRP : 9
DRAM tRAS : 24
DRAM tRFC : Auto
DRAM tRRD : Auto
DRAM tFAW : Auto
DRAM tRTP : Auto
DRAM tWR : Auto
DRAM tWTR : Auto
Command Rate : 1
CHA Round Trip Latency : Auto
CHB Round Trip Latency : Auto
Memory Low Gap : Auto
Memory Remap Feature : Auto
PCI MMIO Allocation : 4GB To 256MB
Memory Hole : Auto
DRAM Margin Ranks : Auto
*CPU Configuration*
Configure advance CPU setting
Module Version :
Manufacturer : Intel
Intel (R) Core (TM) : Intel Core i5 650 3.2GHz
Frequency : 4080MHz
BCLK Speed : 170MHz
Cache L1 :
Cache L2 :
Cache L3 :
Ratio Status : Unlocked (Min:12 , Max:24)
Ratio Actual Value : 24
Hardware Prefetcher : Enabled
Adjacent Cache Line Prefetch : Enabled
MPS and ACPI MADT ordering : Modern
Max CPUID Value Limit : Disabled
Intel (R) Virtualization Tech : Enabled
Execute-Disable Bit Capabili : Enabled
Intel (R) HT Technology : Enabled
Active Processor Cores : All
A20M : Disabled
C1E Support : Disabled
Intel (R) SpeedStep (tm) tech : Enabled
Turbo mode: Enabled
Intel (R) C-STATE tech : Disabled

Linx fails during the first pass. I've been able to run 4 passes with the memory at 1360MHz. What do I need to do to get my memory stable?

[PatRaceTin]

intel 32nm 1156 has some issue with dram ratio 1:5 but may not relate to your problem

[nolonger]

Lower RAM speed is 24/7 F@H stable, will try Linx soon. Could it be my modules just don't want to overclock at all?