Asus P5N32-E SLI Plus and clockgen ...

[Cranox]

If u have a Asus P5N32-E SLI Plus can u use clockgen whitout problems ?
Because i got freezes and bleu screens ,reboots with it

If u use it with no problems can u tell me how u did it ( biossettings )

The problem is that if i boot at 10 x 320mhz ( system is 100% stable ) and then i use clockgen 320 -> 321 = freeze , 320 -> 319 = freeze
If i set speed at 266 ( default ) then i can use clockgen up to 310 , then system begins acting weird ( screen flashes ) if i set it then at 311 i got a bleu screen ( Machine check Execution )
I must do this with very small steps , 266-> 268 -> 270 -> 272 ..

I linked ,unlinked , sync , pci 100 , pci 105, 1T , 2T, voltages up, voltages down.
System can boot up and do 3dmarks at 3900mhz , but i can not use clockgen ...

Maybe because this board uses the C55 + MCP55PXE

680i = C55XE + MCP55PXE
650i = C55 + MCP51

[shimmishim]

rumor has it (since i haven't tried yet) that the new beta 1.0.5.3 clockgen works with this board.

[Cranox]

I tried it with with a "old" beta 1.0.5.3 and with the 1.0.5.3 official

[Leeghoofd]

I cannot use clockgen either over 350 fSB on my Striker board, my settings have to be done from bios or otherwise it freezes...

Can you run Intel TAT Cranox, mine always gives some dump error... on the P5BN and P5W it runs fine not on the 680I of mine

[easypanic]

For me it worken instantly, had no problems to get it to work...

Same mobo as you...

[Cranox]

With TAT i get this error ...
http://img152.imageshack.us/img152/6209/tatpm4.jpg

[Naughtyboy]

1.0.5.2 works just fine for me....it finds C55 buy default...

[easypanic]

What BIOS are you using?

[Desert Eagle]

With TAT i get this error ...
http://img152.imageshack.us/img152/6209/tatpm4.jpg

Same error here with TAT

[Cranox]

1.0.5.2 works just fine for me....it finds C55 buy default...

Can u upload that version somewhere , so i can try that version

What BIOS are you using?

Bios 602

[Cranox]

Same error here with TAT

And no problems with clockgen at all ?

[easypanic]

Retested this morning with the Clockgen version I sent you, everything ok here ...

[Naughtyboy]

Using bios 0602 to...but it works with every one of them.

Send me a PM and well get you startetd with 1.0.5.2

[Lestat]

correct me if i am wrong here but TAT only works with intel chipsets ?

this happens with 680i and 650i it cant be used.


and why on god's green earth would you use clockgen on a motherboard where the fsb will go way beyond the abilities of your chip if your using 10x multi.
seems pretty goofy to try and use clockgen doesnt ? huh ?

[Desert Eagle]

And no problems with clockgen at all ?

I'm not using Clockgen @ the moment,but maybe i'm gonna give it a try.


edit: looks like Clockgen 1.0.5.3 works perfect on this mobo!

[Cranox]

It seems that Ntune is the guilty one !!!
I removed this piece of **** and it works now. ( i forgot that i installed this )
Thank u guys for helping me ( was at the edge for caling a priest , thought that my computer was possesed )

[Cranox]

correct me if i am wrong here but TAT only works with intel chipsets ?

this happens with 680i and 650i it cant be used.


and why on god's green earth would you use clockgen on a motherboard where the fsb will go way beyond the abilities of your chip if your using 10x multi.
seems pretty goofy to try and use clockgen doesnt ? huh ?

I think ure right when u say TAT only works with intelchipsets.
320 X 10 was only an example m8.