Here is mine, 680i and q6600
I cannot get my clocks past 2.8 ghz no matter what voltage I do, I think my board sucks or i am doing something wrong :/
Was on a cold night in NYC, I still need to put some fans on it to go even lower
im running a similiar set up (see sig)
try raising your cpu core voltage, or upping your northbridge voltage. i was running 1.7v into my northbridge that night!
highest FSB i could get...
hoping to push it even farther this winter once the temps drop again
Last edited by xdrift0rx; 11-10-2009 at 12:30 PM.
Case---------CM Cosmos (http://www.xtremesystems.org/Forums/...d.php?t=194812 )
Power Supply-CM RealPower 850W
Processor-----Intel Q6600 SLACR @ 3.6ghz 1.44v
Motherboard--DFI x48 UT-T2R
RAM----------G Skill Black Pi 2x2GB DDR2-900 @ 450mhz 4-3-3-6 CR1
GPU----------Dual GTX 275 896MB (usually stock speeds)
HDD----------Dual VelociRaptor 150GB(Raid 0) 320GB Backup
Audio--------Razer AC-1 (On sale on woot for 50$ )
Mouse/KB----Razer Copperhead/Logitech G15
Watercooling: AquaComputer Cuplex HD, MCW 60's, 2x120mm Radiator, MCP655, EK Multi-Res.
Build your PC in a vaccumed freezer. Sounds chilly brrrrrrrrrrr
You guys are really lucky....I'm in Singapore and its like 32-34 degress C here....even on water, its still hot as hell...
We (at least I'm) are not lucky. Be happy with your temps, I have to deal with -50*C (and lower!) right now with the wind chill.
Its 2F/-17c outside here, and inside my chillbox it 4-6F/-16c q9550 under load = 4-6c @ 3.74 @ 1.23v
did some midnight ocing with cool night air and some watercooling, lol i had to stop cos apparently some parts of my rads internal water canals froze and i had barely no water flow and had to stop the session
Evga X58 sli under cascade
Evga X58 Sli ultimate overclocking/ overview/ discussion thread
proud owner of E8600 Q822A435
I picked up 2 1977 bonneville heater cores from a local auto parts store for 15$ each. I still have to run a 100% antifreeze mix but the heater cores have very little restriction and with 2f internal case temps the heater cores do fine. Had emm for over a year now and they have yet to freeze up.
I need to get something set up and hope it stays cold for a couple days until I have a break from work
i5 2500K @ 4.9GHz+ 8GB G-Skill RipJaws DDR3-2000 @1600Mhz CAS 6 Asus P8P67 Pro CrossFire 6970's @ 950/1450
Xeon X5677 @ 4.5Ghz 6GB G-Skill RipJaws DDR3-2000 @1600Mhz CAS 7 Gigabyte EX58-UD5 4870x2
i7-880 @ 4.2Ghz+ (still playing) 4GB G-Skill RipJaws DDR3-2000 @2300Mhz CAS 9 Asus Maximus III Formula MSI Hawk 5770
Out side temp and internal case temp = -17c
Here's a quick shot at load. I didn't load it for long. If I let it run for a while it will go up a few deg.
And yes this chip has 2 very stuck sensors. If I unplug the pump, - once it hits 25c or so all the sensors work again lol. The correct sensors/temps are @ 3c in this ss. The chip clocks well enough so meh. I just picked the chip up on newegg for $249, gonna run it till the i9 comes out.
Been running like this for many years with various setups and other than a few rad issues I've had no problems. Though I do have to keep the pump and a res outside the chilbox. The pump freezes up otherwise.
I also gave up on using a waterblock on the gpu, I go though a ton of graphic cards and buying new blocks got expensive. I usually just swap out the thermal paste on the gpu n vram and use a high cfm custom fan and semi mod the stock cooler. Gtx280 loads in crysis @ 36c-42c temp depending.
I will perhaps get pictures later.
My friend and i did some overclokicking with some cold swedish winter air. It was around midnight and there was a snowstor outside. I think the outside temp was about -15 or so. ALOT of snow though.
What we did was mount a Thermalright Ultra 120 eXtreme on or testrig and then use tejp to mount 2 Schytche Kaze 3000 rpm (144CFM) on it. We placed the entire system need the back door witch has a cat door. We rigged the door open and the builded a "tunnel" of sort between the fan intake and the cat door. The fans sucked ALOT of cold air and snow trough the fans and into the room. We had a very wet floor after just 10min of running. Anyway, we had mounted a standard thermometer on the base of our Ultra 120. I think the temp was 5 degrees, while the rest of the room was about 19 degrees.
To bad our Celeron 430 did not clock as good as we had hoped :P. The CPU temp at 1.6V was about 20 degrees.
CPU: Intel Core i7 965 EE @ 3,8GHz
Motherboard: Foxconn BloodRage X58
Memory: 3x 2GB Corsair Dominator PC1866 9-9-9-24
Graphics card: Asus HD4870 + Accelero S1 rev2 + 2st Zalman 120mm
Cooling: Scyche Mugen 2
Power supply: Antec Earthwatts 500W
moon of the Neptune
55% of Triton's surface is covered with frozen nitrogen, with water ice comprising 15–35% and dry ice (frozen carbon dioxide) forming the remaining 10–20%.Well, That's ambient temperature !The surface temperature is at least 35.6 K (−237.6 °C)
Huhh, i miss living in eastern europe :/ now have to be in California :P
Holy sheet thats cold someone bring some oxygegen and a match
From porche to versa one fell swoop
Intel Core 2 Quad Q6600 G0 @ 3.34Ghz / EK Supreme LT Nickel / Plexsi
Asus Maximus Extreme
2x 2GB Patriot Extreme DDR3-1333
Sapphire Radeon HD 5970 2GB
500GB WD Caviar Blue SATA2
80GB WD Caviar Green SATA2
OCZ EvoXStream 720W Modular
Coolermaster Stacker 830B
AMD Athlon X2 4050e / Coolermaster 101A
2x 1GB Infinion DDR2-667
Connect 3D Radeon X1900XTX 512MB
500GB Seagates SATA2
Antec TruPower 2.0 380W
hello i am new to phase cooling.......i have water cooled many many pc's over my time and are no newbie with overclocking
i want to know how to cool a i7 3960x with phase cooling or tec cooling
i live in australia so usually fairly hot here my i7 3960x @ currently 4.9ghz is maxing out on temps and i want to push it further......i currently have it watercooled with a 320 rad and a 140 rad......temps hitting high 80's under load.....could i use say a coolmaseter phase change from frozen cpu to use this computer for about 5 hours a day......and not have to worry about condensadion (can u set temps dont want like -20 for massive benches just want to runt he cu 5.2ish all the time)......any advice would be helpfulll.....have thought about water coolers or chillers....???? have used chillers before on my aquarium.....but other than that not much experiance....help plz....also all phase units iv seen are 110 or 120v i need a 240v compliant machine here....
You could get a Hailea water chiller like the A500, it works real good.