Intel DDR2 motherboard compatible list

[Sorrow13]

Just ordered some 2GBNQ.
Had good experiences with gskill in the past, figured id give em another run.
Plan on using with asus p5b-e. Any chance you could test it? ive not seen much on the gbnq anywhere. If i need to grab some cheap stuff to boot with lemme know so i can get it.
Stock is listed as cas5 @ 1.8v, if i can get cas 4 at 2.0v ill be happy.

[flou]

Just say that pk+ds4 are compatible with F6.Also overclockable up to 480mhz(prime stable) with 4 etc. Voltage +0,5 -> 2,3V.

[jon_k]

I ran 2x1GB PC8000 DDR2-1000 HZ with an Intel D975XBX2 (BadAxe2) motherboard at 2.28v with 4-4-4-5 timings. It was orthos stable for 24 hours.

[gbeans99]

F2-6400CL4D-2GBPK

Mobo: Intel D975XBX2
Bios: 2333/2507
Voltage: 1.84 on boot | 1.9 tested
Speed: works at 533|667|800

[GSKILL TECH]

hi everyone, please submit the test result with correct format. it helps me to do it. thank you

[cadaveca]

F2-6400CL4D-2GBPK | Intel D975XBX2 | 2333/2507/2643 | Voltage: 1.84 on boot | 1.9 tested Speed: works at 533|667|800
F2-6400CL4D-2GBPK | Intel D975XBX | 1304/1351/1441/1463/1474 | Voltage: 1.84 on boot | 1.9 tested Speed: works at 533|667|800
F2-6400CL4D-2GBPK | DFI CFX3200 | 12-23/ | Voltage: 1.84 on boot | 1.9 tested Speed: works at 533|667|800


Gotta say...these sticks are great. Running Commando now.

[eXo_Ultimate]

I have dfi rd600 mainboard and also F2-6400PHU2-2BNS 2*1 gb=2gb memory.
But it didn't works with it.I'm uptade the new bios but it's still didn't work.
What can ı do now ? Help me pls..

[Cracker]

F2-6400CL5D-2GBNQ | GIGABYTE DS3 Rev.1 | F7 BIOS | Boots up and runs fine @ 1.9v 5-5-5-12, 32M PASS with 2 512mb sticks of Corsair TWIN2X1024A-6400 for total of 3072 MBytes system memory at 400FSB.

I'm posting this in case anybody else has the DS3 and one gig of Corsair and is wondering if adding 2 gigs of this RAM is feasible or not. It definitely is. My machine is now ready for Vista... if only I was.

P.S. Ran Orthos blend for over an hour with no problem. Would run it longer but I actually use this computer.

[Don_Dan]

F2-6400CL4D-2GBHK | Asus Striker Extreme | 0701 | running w/ 2GB of Corsair 6400C4D, bootable at 2.1v w/ 5-5-5-15


This set is compatible with the Striker, running great. I had the Corsair running at 800 4-4-4-12 1T before, changed timings to 5-5-5-15, built in the HK and booted.
Now I'm priming at a FSB of 300 MHz, RAM is at 4-4-4-12 2T at 700 MHz ( 5:6 divider ), voltage of Northbridge is 0.1v higher than stock, RAM is at 2.125v.

[msgclb]

F2-8000CL5D-4GBPQ | EVGA 780i | P03 | No problems, Prime95 + MemTest. Also Memtest86+ ver. 2.0 and Vista's MdSched memory test.

I bought this memory because some other EVGA 780i owners suggested it. After purchasing it I found this forum and was surprised it wasn't listed. Since then I've tested mine using several methods.

DDR2-1000
Booted: Passed
Loaded Windows Vista x64: Passed
Run Prime95 25.5 blend with memtest: Passed
Memtest86+ ver. 2.0: 2 complete + 10 #5
Vista MdSched: Passed

FSB - Memory Clock Mode: [Linked]
FSB - Memory Ratio: [Auto]
FSB (QDR), MHz: [1067]
Actual (QDR): 1067
Actual (DDR): 1000

Memory Timing Setting - Expert
tCL (CAS Latency): [5]
tRCD: [5]
tRO: [5]
tRAS: [15]
Command Per Clock (CMD): [2T]

** Advance Memory Settings **
tRRD: [Auto(4)]
tRC: [Auto(45)]
tWR: [Auto(6)]
tWTR: [Auto(10)]
tREF: [Auto]

[zalophus]

F2-8000CL5D-4gbPQ; Abit ip35Pro-Bios 14; Intel-6550/333x7/1:50-1001;Timings- 5-5-5-15-Auto;Voltage-cpu1.37v/DDR2-2.0v/Memtest crashed system almost immediatley. >CPU voltage to 1.40v-Orthos, Super PI and Memtest failed-> cpu Voltage to 1.41v & DDR voltage to 2.025 & set CPURAM ratio to 1:1.25-835 and sytem now stable under orthos for 2 hrs.

[bikerdude]

F2-6400CL4D-2GBHK | GIGABYTE DS5 | F3

later bios's make the motherboard UNSTABLE when overclocked.

bought a second kit of the above, but now cant run stock setting when in 4GB (1GBx4) mode.

and last week the 1st 2GB (1GBx2) kit died on me, Pc would not boot.

biker

[mikeyakame]

F2-8800CL5D-4GBPI on DFI Lanparty X48-T2R Bios ADC24

Works fine with auto, will POST at DDR2-800 with Vdimm set at 1.90v in bios which is 1.84-1.85v. If you change straight to 1066mhz it will fail to POST.
To run 1066mhz on any strap, Vdimm needs to be set to 1.96v+. Bios voltage reading is out about 0.04-0.06v depending on voltage.

I set 1.985v to get 1.930v.

Timings

Enhance Data Transmitting = Fast
Enhance Addressing = Fast
T2 Dispatch = Enabled

tCL = 5
tRCD = 5
tRP = 5
tRAS = 15
All Precharge to Act = 6
tRFC = 48
Performance Level = Auto
Read delay Phase Adjust = Auto
MCH ODT Latency = 2
tWR = 14
tWTR = 11
tRRD = 3
tRDWR = 8
tWRWR = 6
tRDRD = 6
tWRRD = 5
tRTP = 3
All Precharge to Refresh = 6

-> Clock Setting Fine Delay

DRAM CLK Driving Strength = 3
DRAM Data Driving Strength = 6
Ch1 DLL Default Skew Model = 5
Ch2 DLL Default Skew Model = 5

or

DRAM CLK Driving Strength = 4
DRAM Data Driving Strength = 7
Ch1 DLL Default Skew Model = 6
Ch2 DLL Default Skew Model = 6

Default is 6 / 8 / 0 / 0, which has way too aggressive clock delays for these ICs.

I use Dimm2 and Dimm4 and need roughly these dialled in delays for best system behaviour.

For these setting I use (gives me closest model):

Vdimm 1.985v (reading 1.93v)

DRAM CLK Driving Strength = 5
DRAM Data Driving Strength = 7
Ch1 DLL Default Skew Model = 5
Ch2 DLL Default Skew Model = 5

Fine Delay Step Degree = 30ps

Ch1 Cross Clocking Setting = Aggressive
DIMM 1 Clock Fine Delay = Current
DIMM 2 Clock Fine Delay = 16 Degree (480ps)
DIMM 2 Control Fine Delay = 23 Degree (690ps)
DIMM 1 Control Fine Delay = Current
Ch1 Command Fine Delay = 23 Degree (690ps)

Ch2 Cross Clocking Setting = Aggressive
DIMM 3 Clock Fine Delay = Current
DIMM 4 Clock Fine Delay = 17 Degree (510ps)
DIMM 4 Control Fine Delay = 26 Degree (780ps)
DIMM 3 Control Fine Delay = Current
Ch2 Command Fine Delay = 26 Degree (780ps)

Ch1Ch2 Common Clock Setting = Aggressive

CH1 RDCAS GNT-Chip Delay = 2T
CH1 WRCAS GNT-Chip Delay = 2T
CH1 Command to CS Delay = 2T

CH2 RDCAS GNT-Chip Delay = 2T
CH2 WRCAS GNT-Chip Delay = 2T
CH2 Command to CS Delay = 2T



Hope that helps.

[topdog5050]

i have to manually set my ram setup in the bios.