Search:

Can u please post a pic of the point where i can measure the exact vdimm voltage?

Yeah those are CH-5 but dont be sad that they are CH-5 and not BH-5 ....cause these sticks do clock like crazy.... mine on a FX-51 does 255fsb @3.3v 2-2-2-6 and 260FSB with a bit more voltagte

I have go 2x512mb of hynix dt-d43 which does 270fsb @ 2.7v 3-3-3-10 on k8nneo plat and 1x512mb does 280-290fsb @2.7v

This is a very informative thread i have seen in a long time... direct to the point...nice very nice...keep posting guys...:)

Do u want pics of any specific part from the mobo??? or just the mobo in general..

Hey Nicke i know how to do the vcore of neo2 but i need for the 754pin....pls

Has any got the Vcore mod for the mobo... pls post up..thanx...

btw what is the use of a vdd mod??

I have done the way u asked me to Zajan... and the temp now has dropped from -28 to -34 ... I have not finished with though... but i wanted to know if the processor is working???

btw how will i...

So the liquid is entering due to that fact that there is toomuch R134A gas???

Ok now should i do the little portion thing like this....

Let some gas out and then on the uint and see if it cools...

I used the guide that i found on XS to repair a leak on MACH I by chilly1 and i was successfull(Thanx alot chilly1)... now i have also regassed it with R134A and here is what i get now...

-28c to...

Chill i plan on using a hose like this... is this good ???

btw will fixing a lengthy hose matter??

Now if i get this hose fixed will i have to extend the cap tube to it length??

Should the...

Actually the hose isnt beyond repair... i cant find anyone here in the middle east that can get the copper+prom's hose blazed :(

chill can u pls tell me what to do exactly to get a small leak...

Hi i got the same problem.... now tell me chill what will happen if i bymistake cut the thin curly tubes(cap tupe) ??? can it be fixed???

Btw can i change the flexible tube into a copper flexible...

have u tried coolbit 2.... cause in that there are opengl options....

Ok thanx for the help guys.... i will do as u say... i will not use a VR as u say the bh-5 can handle more then 3.3v....

Btw should i remove the HS off the ram and place a fan on it or just the...

So using the a wire from the psu will do???

Ok if i had to use a VR between them what VR should i use???

thanx soo much

Will using more then 20gauge matter???

Ok thanx for the reply....

So what i can understand is just get any wire.... will the wire from the IDE cables do??? and connect the 2 spots and wola! the mod is done....

Now dont u think 3.3...

hell fire i cant understand the 3.3rail mod....

Should i simply connect those 2 points on the pic with a piece of wire???

If i do what voltages will i get max???

thanx

More ram 9800pro 128mb and 9800XT 256mb and clock to clock 9800XT is faster then 9800pro

That is even if a 9800pro is overclocked to 9800XT ...9800XT is still faster...:)

It is a ground problem my friend... i have it all the time....on my k8nnxp.... and it is also due to high +3.3 line.... keep that like below 3.6v always.....and also check u other rails too .... :)

Damn I would pay any amount to get my hands on those sticks..

Where did u buy it from???

Yes that is how it works for me on the gigabyte k8nnxp :)

Souldburner...

if the khx3200A i get is a bad CH5 then what kind of overclock can i expect.... can i atleast land up getting a 240fsb at aggressive timings??? or atleast 2.5-3-3-11??

MM, I too have the problem of running my corsair pc3500 @ cas2 but will the kingston pc3200 do the job...

btw what is the difference between the khx3200 and khx3200A cause is the khx3200A that bad...