Search:

It's OK, I was being an utter numpty. Hadn't realised that I'd knocked the OC_TGR switch (forcing the CPU onto it's lowest multiplier).

My bad :(

Hi, thanks for replying.

As far as I remember (not at the machine right now, but will confirm later today), I've reset the BIOS/EFI to factory defaults with the exception of changing the SATA mode...

Hi guys, hope one of you can help, or point me in the right direction. I've just finished building a rig based on a Gigabyte GA-X99-SOC Force motherboard, coupled to a Xeon E5-1620 v3, and 32GB of...

Nope, main rig (in sig). I love "tidy" hence why it's laid out as it is :) Cheers for the complement :up:

My server is actually less powerful (Phenom II X3 720BE, 8GB PC2-8500 Kingston HyperX,...

After nearly a decade with my previous case (Coolermaster ATCS-201-SXK, aka the Silver Widow), I had finally outgrown it's usability. With 6 HDD's two ODD's, three video cards, and a board that...

Can anyone tell me what is a "safe" maximum voltage to put through the MCH and FSB?

Just having a little play with bus speeds and max clocks I can get out of this board. Currently running 425MHz...

Ok, I can confirm that I have IDCC installed stably on Windows 7 x64 Professional, on my DX38BT. It allows me to make all changes that I have tried to make (FSB, Voltages, Memory Timings, etc). The...

I think I might have cracked it guys, not 100% on the method to install yet, but once I work out exactly what procedure to take I'll be sure to post it up (working on it now):
...

Mine can boot all the way up to 460x7 (3220MHz), i'm yet to try any higher, but 3300MHz~ seems to be the limit of the actual chip :(

Going to stick it under the vapochill and see if I can squeeze...

Just thought I'd throw mine into the mix, still working on just how stable it is :)

http://i180.photobucket.com/albums/x302/paradigmocuk/3300MHz.jpg?t=1184520012

This is on:

E2140
Abit...

Just shoved a cheapo E2140 in my IP35-PRO (its a stop-gap until the price-cuts), and decided to give it a little bit of a push, can probably go further than this, but seems to be stable so far :)
...

uGuru (shudders at the thought of it) seems to work :confused:

Although I can't actually get that high at the moment, and have no multipliers available in windows, at least its not at stock now.

Before I start guys, I have read (and been following since its creation) the "official" IP35 thread, but haven't seen this crop up:

Just got me an IP35-PRO and an E2140 (until the price drops),...

Surely at this point, especially if the CPU isn't running a load, you run the risk of floodback.

Well, it arrived, and it seems to function ok (not actually got it on a system to test load yet), but unless the sticker lies, its gassed with R404a not R507.

If you had read his last post in this thread you would notice he had a month to wait until surgery, approximately a month ago. Chances are he won't be around to read these replies for a good few...

Yeah, the original and PE versions were only R134a (I had a PE back on my 2.8B Northwood P4), that was good for around -33ºc evap temp under idle, although with it being a vapo, I'd take the temps...

If they are r507 as standard then either the evap head is of poor design, the captube is of the wrong ID or length, or the pressures are wrong (or a combination of all 3).

Not actually recieved...

I assume a regas (R404a?) would improve things a little? Would adjusting the captube lenght help any either?

Well seeing as a QX6700 would technically be a C2Q not C2D, then no, i'm not using one of them :p

It will probably be an E6550, and 3.4~3.6GHz would be nice. :)

Also, seeing as it has been a while since I have used phase, I have also forgotten the intricacies of installing onto the mobo.

I have ordered some dielectric grease and some neoprene, but what...

Hi guys, just picked one of these up CHEAP (thought it best not to pass up), not my first phase unit (had a Vapochill PE back in the day), but its the first time I'll have gone phase for a...

NB voltage is increased, so I doubt that is causing any issues.

Its not the CPU or the Motherboard because I can set any combination of Multi and Bus speed and the BIOS will report it correctly:
...

Ok, read my post again ;)

I can't get windows to see any multi except for 10x!

3x HTT multi works fine at 315MHz (gives me a HTT of 945MHz), its the CPU multiplier that isn't working,...

Sorry for the noobish first post, been out of the PC scene for 18 months or so, and not really extreme overclocked since I had a s478 P4 and a vapochill.

Just about to upgrade to C2D setup so...