Search:

You could also use the same psu, just make sure you connect the pelt to multiple wires and avoid connectors or use a pcie or 3 or 4 regular molexes. Its also advisable to use a multi-rail psu so you...

It's better to use multiple 12V and GND wires and just cut of the molex connector and solder the TEC directly to the psu wires. For me this works fine with a swiftech 24A TEC using an old 2nd hand 30...

Ok cool.

I don't have a card so I can't check but is the uP6210A user to power the memory?

Is the no coldbug bios also withoud ocp and ovp?

I'm not exactly sure how this works but it seems that the chip features a "SMBAllert" which is a alert signal on out-of-limit conditions. Probably this is used to shut down the chip when on of the...

I like this chip :D

http://overklokken.info/images/SnotAap/555/cpuz.png

http://overklokken.info/images/SnotAap/555/1ms.png

http://overklokken.info/images/SnotAap/555/pifasts.png
...

OCP mod works. Depents on the card if it helps with overclocking though.
This will give you around 3A per phase extra, which is 12A in total. So not much but just enough for that extra push. :D
...

Only in China. :mad:

Why not use the supplied software?
It can both set memory and core voltage. :)

Whats printed on the chip on the most left side of the pcb?

Pictures? Does it use a volterra chip?

It was an honour to bench with you guys.

Next time with an ocp mod for some 1300mhz+ damage. :up:

For all the guys benching this card, don't clock the memory to high. It will lower your scores....

The software does work with multiple cards. :)

And I also have a batch script where you can set the voltages of multiple cards to 1.9V at maximum. :D

I also have a SLI and a tri SLI version. Just send me a pm if you want it. :)

Card is for sale btw. :)

I had the same problem with an Asus MF3 during a compo. Motherboard is dead, cpu is still working though. Is now also missing some "contact pads" might be something with bad contact or nog enough...

And a 3dmark06 run:

http://overklokken.info/images/SnotAap/Matrix/3dmark06_30350.PNG

GPUz validation:
http://www.techpowerup.com/gpuz/3vaqa/

Special thanks to tweakers.net and Milan from...

I used the following settings to boot:
Clocks:
bclock: 200
pcie: 100

Voltages:
CPU Amplitude: 900mv
PCH Ampltude: Auto

CPU Clockskew: Auto

I can confirm that the script works for the Asus Matrix GTX285. :D
http://www.xtremesystems.org/forums/showthread.php?t=234082

Don't know about the TOP, could je run 'rivatuner.exe /i2cdump' and...

Had some driver problems in vista, didn't even notice physix switched on (again) until after I was done. So no without physx Vantage score. :mad:


No submission on hwbot, Vantage is with physx....

I think the screenshots say enough.

Vantage: (physx was on by accident :()
http://overklokken.info/images/SnotAap/Matrix/vantage_21855.png

3DMark06:...

And a full size screenshot:
http://overklokken.info/images/SnotAap/1100_NDA.jpg

More testing tomorrow, should be a bit more headroom. :D

http://www.techpowerup.com/103279/ASUS_GTX_285_Matrix_Registers_1100_2452_2800_MHz_Tests_Stable.html

http://www.techpowerup.com/img/09-09-07/84b.jpg

Should be good under ln2 ;)

Congratz Henry and Elmor. :bday2:

Good job :)

I made a sli version:

http://overklokken.info/images/MSI_GTX26/MSI_GTX260L_Voltage_Tool_SLI.bat

Didn't test it yet. Feel free to try. :D
...

Afterburner only goes to 1,3v, or did you 'change' the software?
This goes to 1.8v. :)

And you only need to install rivatuner, no other cr*p. But everyone is free to install what they want. :)