Your problem is obvious,even if the cause and solution is not.You can clearly see in the following pic and the other 2 posts that all the gap should be at the bottom,whereas in your assembly all the...
Type: Posts; User: Thickbrit; Keyword(s):
Your problem is obvious,even if the cause and solution is not.You can clearly see in the following pic and the other 2 posts that all the gap should be at the bottom,whereas in your assembly all the...
Hey thanks.This is about as good as my camera gets.If you need macros of specific areas i can do that or i can borrow a camera for better pics of the whole pcb.
...
Does anyone have or can anyone help with the ocp mod for this xfx 8800gs (same as gt) please ? The ic is labelled BN-9H.Thank you.
http://homepage.ntlworld.com/peter.jones107/8800gs-01.JPG
In all fairness i have to admit that one of the two controllers i paid you for and which were supposedly sent to Gray mole was in actual fact owed to him for some work which he did for me.The other...
Are these the same 2 controllers i paid you for Johann and never recieved ?
I am still waiting for a resolution to some business between gray and myself,the same business i originally posted about some 4 months ago now.See :-...
I am trying to perform the mod from http://www.vr-zone.com/index.php?i=4756#Scene_1 on my bfg 680i but it won't go quite right.I understood that a bfg should be the same as evga and my early...
Nice going mate,lets hope you have the other one ready for these 2 ultra's by xmas,lol.
I too am unable to contact Gray Mole regarding some business between us,i leave messages on his answerphone,but it would seem he is avoiding me and i am beginning to change my opinion about a guy i...
Hi,which of my 3 mobo's is likely to be best for getting the most from a qx6700 under an R402a s/s.I want to set up for a bench session and don't have time to test all 3.I will run either 1 or 2 8800...
I think you may just be pushing it too hard,i don't like to see display temps below -25c on my units..Upgrading your psu will not affect this issue in any way.
Pushing the boundaries of accepted phase knowledge in his ceaseless quest for freezing perfection,my mate Bazx.Rock on matey.
Hey kayl,nice build,great results and awesome pics.You lucky,lucky dog.
The mach controller runs the elements at 10v.
Both heating elements in my mach have 12v stamped on them,however i'm not sure if that is what the controller feeds it and whether it operates constantly.Check back later and i'll take a voltage...
I dunno if this problem is exclusive to me,but just recently when running high fsb 1/1 around 450+,i lose vcore control.I set say 1.6v or 1.65v,hit f10 and no post,hard reset back to bios,vcore is...
go back to 1503 bios or you could try clearing cmos,that clockgen thing is wierd though,did you choose the right pll chip ?
Boot at less than 500 mhz memory,change trd from 6 to 7 with memset and then clock with clockgen.1407 is old bios,try 1503 or newer.Also the 3/5 devider is going to be too high,as the ram will most...
I think trying to run an e6600 at 445fsb (4ghz/9) 24/7 stable on any 975x chipset is going to be quite difficult,will probably require volt/cooling mods to the chipset and a lucky mobo.Have you...
Mine is a rev 1.02g with the rams in my sig,D9DQW and D9GKX.I would appreciate any more insight into this,as both rams benefit from slacker timings on my p5wd2-p,yet gain nothing on the DH.
I have exactly the same problem,have to boot at <500mhz for memory,set trd to 7 then it'll go up to about 547 and stops dead,still at only 4-4-4.It's probably better for you to run 1/1 with tighter...
Must be,because they are 1gb sticks, pdc22g5600 xblk.
I hope this works.
I'll help if i can guys,i have 2 x 1gb patriot pc5600 xblk with D9DQW.You'll have to tell me what you want me to do though.
As you have water on the northy,you may want to try the chipset vmod and take it up to 1.9/1.95v,but if you already have 1.85v vmch in bios,it probably isn't worth it.You are pretty much near the...