Search:

You're welcome.. Might not fix anything, but I've seen the PCIE link go from x16 to x8 on my UD5, if USB3 turbo is enabled, since USB3 speed boosts take up a lane. And eSATA also takes up a lane...

QD, flaming on these forums is NOT allowed.

Make sure USB 3 Turbo is turned OFF if you're using two crossfired cards with a x1 sound cad. You can also try disabling esata to test. (after you get a RMA replacement card).

Ugh...I never used touchbios before :( didn't even know it worked on p67....anyway i'll see. But thank you for checking with GB about putting the old LLC's back. They can keep the multistep for...

Sin,
You do realize that you could use DVID and LLC together with the OLD F3G and F3H bioses for the UD5 and UD7 P67, right? It was only after GB implemented the *CRAPPY* Multistep LLC (instead of...

Yes it will run nice on P67. You won't lose anything that regular SB doesn't lose on P67. But its best to wait for review samples to be released and out of NDA and then look at how they overclock,...

I used the one that was on the right, if I recall. Try that. Run a LinX test after you replug in the PSU and power on the computer, to test the vdroop.

I used the pencil mod to stop that large vdroop on my P5W, when I had it with a QX9650.
There were apparently two pencil mods, though, with one of two resistors that were right next to each other. ...

This is just bad LLC :(
F8 Final, P67 UD5 B3,
1.415v Bios, LLC7, when playing a single core league of legends...(prime was perfectly predictable at 1.416v small FFT, 1.428v blend).
...

I've always had my settings properly cleared, without using the /C clear dmi, just by powering off after the flash (without rebooting), turning off the PSU, and then holding down the clear cmos...

My "Rift" 8 GB USB drive is recognized in DOS and Bios in all of the USB ports.
I forgot if my kingston 2 GB drive is recognized in all, I think it's only recognized in four ports, and a third party...

Hmm, you're right. I only remembered the vacation until the 1st...forgot they released a bios before that...

LSD: there was *NO* intel firmware update that appeared at the top during the last two bios flashes (F8B and F8C) on the UD5. Unless it "silently" flashed it or something. Are you sure there was a...

Infinite boot loop or overclock failed message (after three restarts)?

What the hell is up with the necro?

I guess no one has bothered flashing the P67 and Z68 new bioses....

But why are so many of these boards frying in the same place? I mean, just IDLE on the desktop? What's going on ....?

Ah.....oh well..only changes are microcode update :( maybe they'll make LLC fix later (I knew it was too soon to expect any changes) :(

Afterburner beta 11 will set the default volts for your card based on its ASIC binning level. So you can see it in the voltage monitoring.
There have been some rumors going around that the cards...

I wonder if it's OVP?
I was able to put my 1175mv Vid card with set @ 1.250v in 3dmark 2011 without crashing, just to check (clocks at 1200, didn't crash; btw it's stable at 1.231v target for hours;...

Elfear,
If you don't mind pushing the voltage, can you test your card and see if you can do 1.25-1.3v on the GPU core (doesn't matter which core clocks you use, even stock, although try your 1225...

Just like I thought.
JUST like with Intel CPU's, lower VID GPUs overclock higher on less volts than higher Vid GPU's...and ID#'s starting with "3" are the lower Vid GPU's.

Mine's 1175v default...

Whoever was the person who did 1200 mhz at default volts, can you run MSI afterburner with the /rr174 command line switch and post the two numbers found? Also what is the STOCK voltage (without...

Try removing and reinserting the CPU?

Every CPU is different, but, to be direct, a CPU with a lower default VID tends to require less voltage for 5 ghz, but runs hotter as a result. The "leaky chip" phenomeon was shown back in the X58...