MMM

Search:

Type: Posts; User: homefry; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    4,842

    Bloodrage Northbridge fan speed

    Anybody know the max rpm speed of the included fan?

    The fan got loud at full blast.

    I need to buy a 40mm fan for another silent system and am deciding between a 3500 rpm fan and 5000 rpm fan.
  2. Replies
    6
    Views
    15,567

    how do you tone down the volume on the panel?

    how do you tone down the volume on the panel?
  3. The strangeness continues. When I set the cpu...

    The strangeness continues.

    When I set the cpu fan duty cycle at 50, 55, 60 %, then the stats I mentioned before don't get updated.

    But when I set the cpu fan duty cycle to 65% or 90% (haven't...
  4. I just found out a pretty strange bug. I can't...

    I just found out a pretty strange bug. I can't see how this was put in on purpose.

    When I set the cpu fan in the bios to smart fan, then the northbridge temp, motherboard temp, cpu vcore, and some...
  5. Motherboard system and northbridge temps don't update

    Speedfan, hwmonitor, and hwinfo, don't show correct system and NB temps.

    On a fresh boot (from the system off state), the temps show -128C in these programs. When I reboot, then it correctly shows...
  6. Replies
    2
    Views
    2,114

    P11 bios and status code light

    So I just updated my bios to the P11 bios and noticed that the light on the status code on my motherboard is out. These lights should last a long time.

    It should say FF, but the bottom portion of...
  7. Replies
    44
    Views
    45,663

    I'm disappointed with the weak heatsinks on the...

    I'm disappointed with the weak heatsinks on the vrm area and the southbridge area. The looks are weak and the size is weak. Competitors have really nice beefy heatsinks on these areas.

    And with 2...
  8. Replies
    5
    Views
    1,360

    Is the cooler making good contact with the base?...

    Is the cooler making good contact with the base?

    The ram sinks can get in the way of the cooler base making good contact. The base is so wide and large to fit all 8 heatpipes.
  9. Could you watercool it?

    Could you watercool it?
  10. Replies
    7,526
    Views
    2,982,347

    Sticky: What cooler is that on your gpu?

    What cooler is that on your gpu?
  11. Replies
    4
    Views
    1,378

    MCP35X on fan controller

    Can the pump regulate speed off a 3-pin fan controller? I know the pump gets all its power from the molex.

    Yes, I know the PWM is better.
  12. Replies
    18
    Views
    1,881

    did anyone even look at the temps in the pics?

    did anyone even look at the temps in the pics?
  13. Replies
    7
    Views
    2,338

    Bump for anyone else with idears.

    Bump for anyone else with idears.
  14. Replies
    7
    Views
    2,338

    In short, I want to find the average delta from...

    In short, I want to find the average delta from water temp to gpu temp for a full cover waterblock under full load.

    40C would be the max temp of the water. This would be a bad-case scenario. So in...
  15. Replies
    7
    Views
    2,338

    Water temperature and actual gpu temps

    I'm trying to make sense of these numbers and how they translate to actual gpu temps. This is not for cpu temps. Only gpu.

    http://skinneelabs.com/xspc-rx120-v1/4/

    Let's say you have a 20C...
  16. Replies
    3
    Views
    886

    I looked at the EK blocks but concerned about the...

    I looked at the EK blocks but concerned about the reports of nickel flaking. It seems that only the acrylic covered blocks are flaking and the place I'm already buying from only has the acrylic...
  17. Replies
    3
    Views
    886

    Heatkiller 6970

    How are the heatkiller 6970 waterblocks? And what is POM in the description?

    How about the Koolance blocks?
    ...
  18. Replies
    8
    Views
    977

    Would it be possible to run the pump at enough...

    Would it be possible to run the pump at enough speed to pump through a gpu block and rad and have TOTAL SILENCE while running at full load on the gpu?
  19. Replies
    8
    Views
    977

    Small quiet pump for 1 gpu cover block

    I need a small quiet pump that only has to pull duty on 1 gpu full cover block and an RX120 (maybe an RX240).

    Ideally, I'd like to be able to control the speed of the pump either through a switch...
  20. Replies
    1
    Views
    363

    MCP35X 4 pin cable length

    How long is the 4 pin cable length on the pump?
  21. Replies
    8
    Views
    686

    what?

    what?
  22. Replies
    8
    Views
    686

    No pictures, but in other threads I've seen what...

    No pictures, but in other threads I've seen what looks like black gunk on people's blocks and they claim to only run distilled and pt or silver.

    I've also seen green gunk.
  23. Replies
    8
    Views
    686

    Copper oxidation

    Is copper oxidation in water just black discoloration or does it eventually build up to be some gunk?
  24. Replies
    137
    Views
    13,549

    I think I read they said that if you remove the...

    I think I read they said that if you remove the top, you break some kind of seal.

    I assume the seal is hidden and on the inside somewhere.
  25. Replies
    2
    Views
    765

    What size fittings were you using?

    What size fittings were you using?
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4