MMM

Search:

Type: Posts; User: musk; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    718

    Tried a new IDE Cable?

    Tried a new IDE Cable?
  2. working mobos

    is there a list anywhere of mobos this works on? I only have P5B-DLX and it doesn't work.

    I would love to find a good mAtx board to use for budget builds.
  3. Replies
    26
    Views
    19,758

    Well, I got the trace paint and it did not...

    Well,

    I got the trace paint and it did not work. I just got repetative reboots, no post. Am I missing something? Has anyone done this succesfully?

    musk
  4. Replies
    26
    Views
    19,758

    Well i just READ the post at ocforums and it does...

    Well i just READ the post at ocforums and it does not work with a silver trace pen. I am going to try the defogger repair stuff like the picture. I will post results tonight.
  5. Replies
    26
    Views
    19,758

    not

    I cant seem to get it to work like that kunaak. My 4300 stays at 200 and boots. Are the two dots on the bottom both painted? Looks likw the bottom one is color of trace.
  6. Replies
    21
    Views
    1,811

    i have done that on both P5B dlx's that have gone...

    i have done that on both P5B dlx's that have gone dead in the middle of the night. i even put one of these on there with a 40mm fan and put heatsinks on the mosfets. 2wice now :slapass:

    I have 2...
  7. Thread: GA i-ram 5,25''

    by musk
    Replies
    33
    Views
    2,068

    Gonna plug a Hipro Maximizer in it????? :D

    Gonna plug a Hipro Maximizer in it????? :D
  8. Replies
    21
    Views
    1,811

    I bet my eye that its the mobo. The same thing...

    I bet my eye that its the mobo. The same thing happened to me not long ago. Everything was fine then boom, gone. Mobo dead. Powers but no post.

    I didn't have gear to test so I took it to the comp...
  9. Replies
    73
    Views
    13,817

    You got me :) Its was the bus speed I was...

    You got me :) Its was the bus speed I was bragging about.

    Didn't mean to jack this thread either.
  10. Replies
    73
    Views
    13,817

    here...

    here

    post 58 above
  11. Replies
    73
    Views
    13,817

    I will as well. I failed after 6 hours at the...

    I will as well. I failed after 6 hours at the above settings.

    I had NB, FSB termination etc at lowest voltages. I will do large later.

    9 vs. 1 is a big difference
  12. Replies
    73
    Views
    13,817

    gots 9 going

    http://img.photobucket.com/albums/v475/musk/orthos3.jpg
  13. Replies
    73
    Views
    13,817

    It is a L629B stepping. I was able to get 19...

    It is a L629B stepping. I was able to get 19 hours of Orthos at 510 x 7 1:1 4,4,4 Priority 1.

    I will get that pic up. I failed after 6 hours on priority 9, 400 x 9 at 1.3v

    It is running now ...
  14. Replies
    73
    Views
    13,817

    Very nice

    Very nice chip. I think I have a winner as well. I am running priority 9 right now to see what happens. :toast:

    Damn Image resizing, too late for this crap.

    will post pic tommorow.
  15. 8 pin ?

    My PS has 2 12v connectors but only one fits. I dont get it. They fit in the DFI Expert so why different on P5B Deluxe?
    I have a Liberty 620w

    Anyone?
  16. Maybe configure one of these ...

    Maybe configure one of these

    http://www.boxxtech.com/products/3DBOXX/8300_TechSpecs.asp
  17. Replies
    4
    Views
    1,371

    clockgen for AM2 boards - M2NPV-VM ??

    Does clockgen work on this board, or any AM2 board?

    I am at work and am blocked from getting to this info.

    Thanks
  18. Thread: Mixed Memory...

    by musk
    Replies
    4
    Views
    853

    I am guessing that this is on the Mobo listed in...

    I am guessing that this is on the Mobo listed in your sig A8N-SLI

    If so are you set to 1T command rate? If so Try 2T. Check your bios and flash to an updated version if its old/original.

    Did...
  19. Thread: Mixed Memory...

    by musk
    Replies
    4
    Views
    853

    Spd

    Do not use SPD. Go in and change your memory timings to match the looser of the 2 sets and see if that works.

    musk
  20. Replies
    242
    Views
    19,767

    results

    Well I was able to run my new set at 260 3,3,3,8 in my shuttle SN25P. CAS 2.5 wont post.

    Not too bad. I will drop them in my A8N32-SLI later and see what I can get them to. I have a opty 165 so i...
  21. Please post when you confirm the IC's. are...

    Please post when you confirm the IC's.

    are these the modules?

    If so;

    Lurking underneath the classy but effective heat spreaders, lie Infineon -5 64M X 8 Revision B IC's that have been speed...
  22. Replies
    1,952
    Views
    310,439

    I am not super impressed with the xp120. Lots of...

    I am not super impressed with the xp120. Lots of people like the Pig Typhoon.

    If you mean the top bracket, piece of cake, unscreew and mount the one that came with the xp120 using the screws...
  23. Replies
    1,952
    Views
    310,439

    Yes you can put the pipes towards the left. works...

    Yes you can put the pipes towards the left. works great.

    If you use the xp120 you do not need to remove the back plate.
  24. Replies
    1,952
    Views
    310,439

    Thanks for the tips. I disabled peg link and ran...

    Thanks for the tips. I disabled peg link and ran a divider. Worked! I am able to run sweet at 280 x10 with the 183 mem ratio. Not bad at all.

    Thanks again
  25. Replies
    1,952
    Views
    310,439

    3D issues

    I am not having any trouble overclocking my cpu but my 3d will not work at all when overclocked.

    I have a optie 148, 2gb mushkin redline and a 7800gtx.

    I am able to prime all day long at 270x10...
Results 1 to 25 of 198
Page 1 of 8 1 2 3 4