I'm running 3DMark Advantage on my system and the CPU clock is not reporting correctly - see below.
Has anyone else seen this? I ran a performance trace during the CPU test and found that 3DMark...
Type: Posts; User: x-built-Stan; Keyword(s):
I'm running 3DMark Advantage on my system and the CPU clock is not reporting correctly - see below.
Has anyone else seen this? I ran a performance trace during the CPU test and found that 3DMark...
Has anyone has Turbo EVO stop working? When I start mine it looks like its running (in task manager), but the window never comes up. I even tried uninstalling and re-installing and resetting the...
Thanks - got it - CPU-tweaker :up:
Does anyone know of software that can be used to dynamically tune the memory on the X58 chip? I used to use nTune on the nForce chips.
DaddyJaxx- that avatar is just wrong. Someone's going to have an epileptic fit.
Does anyone know if this board is discontinued? Everyone seems to be out of stock. IF it is - what's next with Gigabyte and the 1366?
Is anyone running 4-Way SLI with this board? If, how is it working out?
Zalbard,
How about separating the groups by those running all their CPU theads and those just running the cores. I notice that many people are just running the cores to get into the 5+ group....
:welcome:I'm running BIOS 0095 with a 980X. THe BIOS work very well so far. If you are running a 980X recommend staying away from 1102 (production). I have some issues with it reportingthe CPU temp...
:shocked:
22V vCore at 1.6GHz - dude you got robbed :rofl:
That has got to be the worst mistake I've seen yet.
According to the rules on page 1 of the forum - only the CPU-Z window showing the frequency is required. While I appreciate that other have showed the CPU-Z memory page - it is not required.
...
Finally made it LinX stable - 5.0022GHz :D
Submission is in :up:
Details are in signature
I also have the 8 and 4 connected with plenty of power. Ca ot running multiple vid cards yet - sot the PCI-E is not loaded. Eventually I'll get to 4 580s in SLI.
Has anyone noticed that their CPU tempertures are not showing up in CPU-Z hardware (V1.17.0 Driver version 135)? Mine did at one time. AThe temp sensors must be fine because all cores show up in Real...
Donmarkoni is right - enable the Line load calibration to full :up: you won't get too far overclocking without it. The vdroop will make the whole process pretty frustrating.
You should also set...
All paid :D- throw another core on the barbie.:up:
FAILURE on the 19th cycle :down:
Retuning for tonight :yepp:
donmarkoni,
Phase change is not that expensive. I got mine for less than $700 including shipping from Taiwan to California.
Brama, Donmarkoni, thesaucier - thanks for the info on the memory voltage.
I'm making a run in LinX now 5.022GHz. About 3 hours remaining.
I'm running the OCzs (see signature) which are rated at 1.65v. When I try to set that inthe bios, I get a warning saying that 1.65 will damage my CPU. Does anyone know why? I'm running a 980X - first...
Yes. -15C @idle, -5 @100% load :)
Here are the settings that I am running right now:
Any suggestions would be appreciated - I'm looking for 5GHz LinX stable
Bios 0095
CPU 980X
Target CPU Frequency 5054MHz...
Does anyone have a LinX stable Bios settings for a 980X @ 5.054GHz (133x38)?
I just flashed the Bios to 0095 using the EZ Flash 2 Bios Rom Utility in the Bios tools section. Everything worked fine. :up:
Give it try.