Search:

I'm running ripjaws in my rig, they run great. The heatsinks are very short so should do just fine with any heatsink. I can't get my full 8gb stable, but haven't played much with it and think one or...

The weld poses a problem as most plumbing weld is a copper-tin alloy, which is fine and dandy in larger areas, but in the case of the barbs has a high chance of breaking due to pressure from tubes or...

sb doesn't throw off to much heat btw

Unlike Foxconn that expected people to send all dead boards to newegg from the USA you call that support?

Even have had ASUS call me in the past about a video card that died saying they didn't...

I've been water cooling long before places starting making gear that was sold every where, no the inside of the blackops contained welded seams throughout the whole block which was the problem. The...

See your lucky enough to live that way, people that live in America have ZERO support on that end, were told to RMA to newegg and expect that to work if newegg didn't have it in stock or if wasn't...

heh, had the same problem with my blackops USING an ACETEL top and NEVER touching the Alu top, not only is the problem with the top, but the welds inside of the block, trash the block period. Never...

Asus has been the best company I've ever dealt with before (save ram wise which Patriot rules there), they've taken back motherboards and video cards I didn't even have sinks for anymore other than...

just rock it back and forth and it should wiggle off

any am2 block will work, the layout didn't change between the two.

thing is it is bled, no air in that I know of, does it just hooked up to a 355 with a res top as well no rad no nothing, just barbs and tubing.

While I love this block and does a great job of cooling I have an odd quirk with it, it hisses. I have 0 air in the system and no matter how it is plumbed it still hisses (even tried just pump and...

whelp, the deal is sealed for me, never again will I buy a foxconn product if all they can do is lie about things. But one of my main questions is why did they bother to release the older x48 knowing...

Pata is a pita in my book, all I want/need is sata and esata (which esata can run off of normal sata bus as well, as other manufactures have done it before).

casted my votes, and when are you going to add the "What date do you want us to release a hardcore AMD 8XX AM3 board" question?

This is one of the most important questions to me, I've always wanted to upgrade my dvd drives but with onboard Sata so limited I cannot. I currently use the blackops and have all 6 filled with hdd,...

Nah, I think it should be out by April 3009

reserved for more pics

This will be updated as work progresses, will be a few months in the making.


Hardware list:

Case: Custom Navig Benching Station.

Motherboard: Foxconn Blackops (to be changed in the near...

well, he is using 7/16 tubing on 1/2 barbs so I'm sure that it's not leaking that way, how tight are the barbs tightened? I found hand plus tight plus 1/4 turn with a socket is plenty tight and won't...

Now something else that does effect the amount they tighten down is the tubing itself, stiff/hard tubing doesn't go as far, while limp/soft tubing can go all the way. Another thing is how clean and...

yeah, they run great without the watercooling part, just some air moving over them is good enough.

Cooler Master HAF 932 is a great case too, fit's a 360 in the top with no mods at all, and plenty of room to work with inside. Also it's on the cheaper side too, usually floats around the 150 mark.

well, it will *work* with closed corner fans, just requires a little modding to open up the closed corner which I have done more than one myself.

if fully bled, shouldn't be a problem, although I have a feeling bleeding is going to take a turn from a PITA to a nightmare. Only one feature I wish would be added to the newer MCR is a bleed screw.