Search:

<333333333333333 we get the direct drives again!!!

:O

stephen MSRP on the direct drives?

Tim u guys really should make a backplate for us and your blocks.

;)

>.<

I get under 20C idle on my gulftowns with a block dating 2 yrs... :X

idle means nothing... its load values spread (the difference between idle and load) which are important... and even...

i can haz over 9000!!!!

A GT, or something near it that wont cost more then the radiator when you get 3.

To get a 140mm san ace it will cost roughly 38 dollars each... that is ouch.
I saw a 140mm nidac fan.. ala GT,...

We thought it was graphite... then tony from OCZ showed us how bad that idea was..
Turns out that graphite was hydrophobic.. and well... thats bad if u want water to transfer heat.

I would...

0...

i dont use 140mm radiators... :X

Personally i dont like 140mm radiators... not enough fan selection for them.
Also u cant get a GT for a 140mm radiator.

But everyone on this forum...

tibor any chance of getting a shot of the plate itself?

Id like to see the channels...

Looks like a nice block tho...

actually im going though withdrawl...

doctor told me i am intaking too much caffine and its not going well with me, and told me to lay off.

So yeah... im a bit grumpy... :\

But its mostly...

koolance is the only LC company that gives u warrenty if u open the pump so u obviously have no idea WTF ur talking about. A pmp-450 is a D5.

Swiftech says u should use pinesol to clean ur pumps...

the hardest part in bleeding is at the radiator...

especially if its hanging from the top with the barbs pointed down... this can be a newbie killer at bleeding.

Other then that.. dont worry......

Here for you op:
http://i125.photobucket.com/albums/p73/aigomorla/Miyuki/IMG_1335.jpg

it works fine... been using them on miyuki b4 i shelfed her...
...

i meant to say... go with what u think looks the nicest.

Dont worry about pure raw performance as your first setup, as your missing half the physics to understand it properly.

Go with what your...

yeah... op... the moment u came in with money is no object, that tend to set yourself up for a bullzeye...

typically unless u have post count like mine... and u known to splurg big time... a...

PWM also goes by processor load.
I tend to set mine per load basis.. to control usage... you can set it up as temp, and have it go by motherboard cpu temp, however we all know how inaccurate those...

u know op, seems like you really dont care what the vets here say.

let me tell you this as my last post...

there is probably less then 10 people in this forum who understands what ur doing and...

do you even know what a compressor is?

Do you know how phase change works?

Do you know what is evaping and how thing are getting cold?

Im not just asking this on your sake.. its the answers...

u can not use a fridge compressor..

they are not designed to be on constantly..

you want to use an AC.

And this topic is in the WRONG section as well:

Chilled Liquid Cooling. ...

u wont miss 1C unless ur me and just picky about having the best.

5 months???

did u get grounded by your parents? :P

You can leave the system as it is...
However the moment u start up again, i suggest you do at least a flush.

Or if better yet, i...

PWM is the future if you want quiet...

get higher powered fans.. less of them use PWM.

and i dont trust NZXT... i dont care how great of a company they are...
Get a SUNBEAM... they are proven...

yes go sideways as it will probably give u the best.
Going up and down u might not get that great of a cooling vs side to side.

This is why i am skipping sandy-e entirely and waiting on ivy B. ...

i use a KL-360 on a custom vapor nozzle. :T

If not, id think id get the EK HF.

I know performance lies there from the many hours of testing the guys here have done.

The XSPC.. i dont...

It looks good the way it is, without majorly reduing your loop order.

did u messure the clearance of your PSU?
Can it fit without kinking that tubing after you have the rear cabling that comes...

im lost in general why do you need something to push water out?

if your having bleeding issues, it means your loop order was slighly messed up, or your tubing routing is messed up.

If your...