Search:

My goal is to set a modest overclock of 4.5ghz for gaming. Just had some questions about Overclocking my i7 2600k on the P67 UD7 Gigabyte board. Can you look over these bios settings make sure I'm...

Let me guess, something will be off and you will post a message saying such and such will not fit with ek block. Months and months after you purchase... Hi gap67ud7 block

I'm not going to RMA it. I'm going to take a dump on it. I'll post pics later!

not much, quarter of an inch? Maybe tiny bit more. Do you even have to have cards locked in place? Or would they be okay if 90% in slot?

So if I don't let the bottom card completely lock in I can get them to connect. I'm just worried that they will lose power or something later by not being locked in place.

I can't get the 2 cards lined up good enough for my connector fitting. If I pulled out my bottom card a little I could probably get them together but as of now I can't get top card seated correctly....

I dunno. I have EVGA. Maybe they are different or I'm just doing something wrong. But I doubt it, I have installed the block perfectly and no matter this card will not fit.

118033So close but so far :(

Yes give me a minute. Restarting phone, email not working. BRB!

Here is anchor hitting the block.
118032
This is a EVGA 580 3gig card btw. 6990's fit I guess.

or you talking about actually cutting into the block? I'd never try either so doesn't matter ;/ Oh well just another $100+ wasted in this hobby. Nothing really new. EK moved to bottom of my list...

Can you cut the anchor off Graphic Cards? I'll probably just take this piece of crap off and use the original gigabyte cooler. I've been slowly collecting so many parts and doing some really cool...

So I bought & installed the EK nickel/plexi P67A-UD7-B3 block way back when B3 first came out. Description at the time had ZERO information about not being able to use the very top PCIE_16 slot with...

Also I bought some SR-1's. These things are far from clean. Am I the only one that checks water in clear bowl after pouring out? My god so many little white particles. Maybe I'm trying to hard. I...

I've done this for days and days. I still get particles after I shake the radiator with water inside. Dumping out into clear bowl. Filter system does not clear out particles good enough.

GT's best bet. 1850rpm max. Can go lower but also medium Yate loons would work good! Cheaper and quite efficient

I responded to this way back, and now regret to inform I'm on the same boat. I can no longer send back to retailer and have yet to email XSPC. All 4 XSPC360's are non stop particles :(

I should also add that I've ran all 4 radiators through a filter loop system I copied from a post here. Reservoir/rads/filter for hours on end and still get all these particles.

I've had the worst problems with radiators lately. I'm trying to find a good triple radiator for low speed fans without the problem I'm running into. I've cleaned 4 xspc 360 radiators at least 50...

http://www.xtremesystems.org/forums/showthread.php?t=270567

I used distilled+silver with my old EK 280 nickel blocks with ZERO problems. Now with the newer EK nickel blocks they are trying to say...

+1

Mine are lookin and coolin great!

and then there was SILENCE... :ROTF:

http://www.koolance.com/technical/quick_disconnect_shutoff_couplings/qdc_fittings.html

Easiest way I've found so far. I have 4 sets in 2 loops. Works great!

Yeah I don't mind the price. I've talked to Martin and I'm going forward with his service. I tried sleeving and you really have to work at it ;/ Would take me a long time to get really good and I'd...

Yeah! Thanks!~

And uses the mdcp sleeving.