Search:

Type: Posts; User: iNF3rN0; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    4,623

    What refrigerants are you planning on using for...

    What refrigerants are you planning on using for each stage?
  2. Replies
    20
    Views
    7,613

    This looks like alot of fun! I am curious why...

    This looks like alot of fun! I am curious why capillary tubing is used rather than a TXV. Is it because of cost?
  3. Replies
    239
    Views
    127,681

    Nice to see proper vibrasorber orientation ;)

    Nice to see proper vibrasorber orientation ;)
  4. Replies
    239
    Views
    127,681

    I was always told to mount the vibrasorber on the...

    I was always told to mount the vibrasorber on the discharge line parralel to the crankshaft to properly isolate from compressor vibrations. When your compressor is running the torque and vibrations...
  5. Replies
    2,284
    Views
    2,155,520

    Sticky: This started as proof of concept. It all fit on...

    This started as proof of concept. It all fit on paper. So I took it to the next level http://i.imgur.com/GsAs5uy.jpg
  6. why dont you use an electric hot water kettle,...

    why dont you use an electric hot water kettle, cut the cord on it and use an inline reostat/light dimmer switch and use and ammeter to accuratly create your heatload. It wont be 100% accurate but it...
  7. Replies
    5
    Views
    755

    130324 130325

    130324

    130325
  8. Replies
    5
    Views
    755

    Thanks CrazyNutz, I purchased this Lepage Marine...

    Thanks CrazyNutz, I purchased this Lepage Marine adhesive from home depot and it seems to have worked. I drilled a bunch of holes around the square opening i cut into the rad and secured nuts behind...
  9. Replies
    5
    Views
    755

    what type of epoxy?

    Ok so I'm building a scratchbuilt sff lanbox and I have a dual 120mm swiftech rad that I want to modify. I want to add a fillport/window into The top of the radiator. The end cap on the rad is brass...
  10. Thread: Need help

    by iNF3rN0
    Replies
    5
    Views
    1,036

    so no one can give me anything?

    so no one can give me anything?
  11. Thread: Need help

    by iNF3rN0
    Replies
    5
    Views
    1,036

    My size restrictions are 4.75" height, 7.5" deep,...

    My size restrictions are 4.75" height, 7.5" deep, and about 15" wide. I've seen some horizontally mounted scrolls, but I wonder if a small scroll that's intended to mount vertically can run...
  12. Thread: Need help

    by iNF3rN0
    Replies
    5
    Views
    1,036

    Need help

    Need to find a compressor to fit inside my Corsair 800D. I have been imagining a condenser mounted inside the top of my case with the lineset hiding behind the drive bays and a horizontaly mounted...
  13. Replies
    16
    Views
    1,514

    Well I was planning on having just one MCP-350...

    Well I was planning on having just one MCP-350 pump in this system with a custom top using 1/2"ID tubing. From what ive read, maybe I shold run the cards in paralel then. unless I get a second pump.
  14. Replies
    16
    Views
    1,514

    Thanks again guys. I'm getting a 3x120 rad on...

    Thanks again guys. I'm getting a 3x120 rad on top. Also gonna put an existing 2x120 rad on the bottom. Could someone tell me why running the vid cards in serial instead of parallel is better?

    Btw...
  15. Replies
    16
    Views
    1,514

    Thanks a lot guys. I'm not new to watercooling. I...

    Thanks a lot guys. I'm not new to watercooling. I just have not been as Xtreme as Ive wanted to be in the past. Ive had a block on my cpus since my athalon xp 2500-m :) Ive been using switech blocks...
  16. Replies
    16
    Views
    1,514

    I forgot to specify that i do not want anything...

    I forgot to specify that i do not want anything hanging outside my case. I lan and transport my computer way to much. Its not that I dont wanna mod the case because I wanna resell it later, Its more...
  17. Replies
    5
    Views
    700

    Compressor fitment!

    Im curious if there are any good compressors under 5 inches in height because while I stare at my empty 800D that im about to fill with watercooling equipment, I just have this Xtreme vision of a...
  18. Replies
    16
    Views
    1,514

    New configuration dilemma

    Okay, so heres what I want on water:
    i7-950
    2x evga gtx460 1gb's

    If i dont modify my 800D, then Im thinkin one loop, single tfc 3x120mm rad on top. Im just worried about my order of flow. I was...
  19. Replies
    11
    Views
    5,423

    I have a question, I just bought a x58 ud5 board...

    I have a question, I just bought a x58 ud5 board and I want to know what kinda block I can use on it. I do not know what the difference between the EX58 and the X58 board is. I contacted EK to see if...
  20. I too would like to know which block wouldn't...

    I too would like to know which block wouldn't fit. I just ordered this board, its on its way right now. I was going to order the EK-FB KIT GA X58 which is supposedly good for the EX58 ud5 but on...
  21. Replies
    4
    Views
    366

    Hmmm, interesting. Then I guess ill stick with...

    Hmmm, interesting. Then I guess ill stick with single loop. But I think I'm gonna get a second pump, run them togethar. Space isn't really an issue though, I don't plan on haveing more than 5 drives...
  22. Replies
    4
    Views
    366

    Any reason why single pump single loop? There's...

    Any reason why single pump single loop? There's gonns be two rads, cpu block motherboard full coverage block, and two video card full coverage blocks. Wouldn't al this be to restrictive for a mcp350?...
  23. Replies
    4
    Views
    366

    Need opinions and insight

    Just ordered a bunch of new parts. Well I pretty much ordered all the internals for my Obsidian 800D.

    i7-950
    X58 ud5
    6gb corsair dominator 2000mhz
    2x evga 460 1gb

    I already have a swiftech...
  24. Replies
    147
    Views
    30,761

    Im really excited to see the end result. Keep it...

    Im really excited to see the end result. Keep it up
  25. Replies
    2
    Views
    998

    Condenser mounted horizontal

    Can a condenser still function properly when mounted flat horizontally? If a conventional condenser wouldn't work that way, are there any that can? I mean in theory it could work because the velocity...
Results 1 to 25 of 60
Page 1 of 3 1 2 3