The throttling can kick in because of temps or power draw from the VRM (even if temps are fine).
Source...
Type: Posts; User: new-b; Keyword(s):
The throttling can kick in because of temps or power draw from the VRM (even if temps are fine).
Source...
Picture on Koolance website shows screws there.
http://www.koolance.com/water-cooling/product_info.php?product_id=1016
I've had my 50z running since 2004... currently on a GPU only loop, still running great.
Swifty 355 and XSPC top (running fine for 2 years)
Ok, the only other thing I see mentioned is about the JMicron SATA Driver:
※This driver provides functionality for the onboard SATA RAID Controller.
※ This driver installation is necessary for the...
Go to Onboard PCI Device
enable "Storage Controller"=This option enables or disables the JMB363 controller that controls both IDE1 and eSATA1 ports.
then select "Controller Mode" this sets the...
Had this board a year ago...don't think two 4770's would work too well in crossfire as the pci-e layout is 1 x16 and 1 x4 and these are older 1.0 slots, so effectivly x8 and x2 by todays standard...
FWIW= Ambient about 25c
loop
8500 @ 4Ghz
DD-4870-X2 Water Block
DDC+XSPC top
BlackIce GTS 360 with High speed Yates in pull
..Idle and 10 min game load
...
I just got one of those 4x Kolance shrouds with the same idea in mind... but the fan hole spacing is off on the shroud (estimated guess I'd say it's 17mm). Just a heads up in case you go that route.
For me, cold boot instability came down to vMCH.... try raising it 1 or 2 notches.
"This board supports 30A per phase and delivers a total of 180A to the CPU."
Source= http://www.anandtech.com/mb/showdoc.aspx?i=3508&p=4
I've built 6 or 7 systems with the "R" board and so far all rev 1.0 north bridge coolers faced one way and the rev 1.1's the other.... all run just fine so there probably is no "wrong way".
I've got a Q827A353 8500 in my rig (in sig), but the mobo went on me before I could stretch it's legs.....last thing it did was 16hours prime stable @ 3.8ghz
with 1.216v load. The CPU has a vid of...
Any info on new revisions being released?
Someone on another forum posted they received a UD3R rev1.1 board
http://img.photobucket.com/albums/v150/new-b/picture002tv5.jpg
I was getting this while playing Far Cry 2... sounded like it was coming from the socket area, but i used some tygon tubing (one end to ear, moved other end around socket area to isolate the noise)...
The UD3 & UD3R share the same bios (F3) while the UD3P has a seperate bios (F4).
Yea...I hear the same thing under heavy load (stock volts right now to) and it seems to be coming from around the top vreg heatsink...right about where PcCI2iminal lost his mosfet :(
http://www.gigabyte.us/FileList/WebPage/mb_080924_ud3/data/tech_080924_ud3_models.htm
http://img.photobucket.com/albums/v150/new-b/ud3.jpg
http://img.photobucket.com/albums/v150/new-b/debug.jpg
I used to run that mem before I switched to a 2x2gig kit, had no problems with them.
Yes... there is a known problem using both apps at the same time.
Correct.... All you need to change is in the exact mode.
D'oh......I just re-read my post...I meant the xtra beep is a little longer than the post beep lol.
I get that too (lower pitch & a little longer than normal post beep?) but have never had a problem when it happens :shrug:
Sounds like you still have C1E enabled (drops multi to 6 when idle). Put a load on cpu and see if the multi goes up.