Search:

Type: Posts; User: DoGMaN; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    2,162

    Certainly some thing I would not want to take...

    Certainly some thing I would not want to take responsibility for. I did mine last night with no issues. It is running over 20C cooler now. If you take your time it is not overly difficult, just be...
  2. According to http://www.coolingconfigurator.com/...

    According to http://www.coolingconfigurator.com/ EK has a block that will fit on your first choice card. Check it out.
  3. Replies
    190
    Views
    72,411

    Incredible work lowfat, absolutely beautiful.

    Incredible work lowfat, absolutely beautiful.
  4. Replies
    17
    Views
    3,435

    Very sexy.

    Very sexy.
  5. Replies
    10
    Views
    1,312

    There are two ways you can go about it. Buy a...

    There are two ways you can go about it. Buy a 3pin to 4pin connector or you may have one laying around some fans come with them. If not you just need to tie in the yellow and black wires from your...
  6. Replies
    0
    Views
    1,056

    Dual 280s in a Fractal R4?

    I'm looking at rebuilding my setup in a Fractal Designs Define R4. I'm looking for keeping things as quiet as possible so I was tossing around the idea of using 2 dual 140mm rads. I know that I can...
  7. Beautiful work! Really well put together I love...

    Beautiful work! Really well put together I love it.
  8. Thanks Sin is there any way to over ride this...

    Thanks Sin is there any way to over ride this behaviour?
  9. Replies
    842
    Views
    216,419

    All compression fittings can be a pain at times,...

    All compression fittings can be a pain at times, but god how I love the way they look. One thing I have figured out after years of installing and removing them is that if the tube is heated a bit it...
  10. I am loving my G1.Sniper M3 board but I do have...

    I am loving my G1.Sniper M3 board but I do have one small gripe. On power on the CPU fan doesn't start for a few seconds. It then spins up to quite a loud RPM before dropping back to being silent. ...
  11. Replies
    36
    Views
    3,158

    A good sync rate is usually running 80% of the...

    A good sync rate is usually running 80% of the lines maximum capacity. Once you exceed about 90% you develop problems. Think of it like trying to shoot a fire hose into a dixie cup. If we take my...
  12. Replies
    36
    Views
    3,158

    Not exactly. All main cables are shielded and...

    Not exactly. All main cables are shielded and bonded to reduce noise. For the most part all buried service wires that have been installed in the past 5 years are also bonded. No wire in a...
  13. Replies
    165
    Views
    25,849

    1. I generally use my own T fitting for...

    1. I generally use my own T fitting for fill/bleeding so I personally would prefer not to have it.

    2. I'm one to favor performance over aesthetics, so it looks good to me. As long as the price is...
  14. Congrats bro!!! Always good to see another one...

    Congrats bro!!! Always good to see another one thrown into the trenches ;) JK Anyhow my best to you and yours, many sleepless nights and wonderous experiences await.
  15. Replies
    16
    Views
    1,101

    I run straight Distilled. I do however have a...

    I run straight Distilled. I do however have a small silver rod epoxied into a brass stopper plug. I've run dyes, still do at times for leak testing but I've found that just straight distilled is the...
  16. Thread: crazy idea

    by DoGMaN
    Replies
    10
    Views
    984

    Find an old restaurant that is being remodeled or...

    Find an old restaurant that is being remodeled or closing and try to scoop one of the flash beverage chillers. It will basically be ready to run once you pull out the old stainless steel beverage...
  17. Replies
    11
    Views
    883

    It was fine when I bought it, it just seems to...

    It was fine when I bought it, it just seems to have accumulated something over the years that it sat. I tried to take a pic but it doesn't come out clear.



    Yah I know enough not to use...
  18. Replies
    11
    Views
    883

    Best way to clean an Acrylic res?

    I found an old acrylic res I bought some years ago but never used. It seems to have some "grit" on the inside walls. I've tried flushing with hot water and rinsing with vinegar but the "grit" is...
  19. Thread: Need some help

    by DoGMaN
    Replies
    17
    Views
    1,048

    My opinion would be to grab the XSPC RS240 and...

    My opinion would be to grab the XSPC RS240 and some 13mm (1/2" for our American friends) tubing. See if the store has the new Swiftech GTZ. While the GTX would work just fine the new mounting...
  20. Poll: I was (and still am) rather disappointed that the...

    I was (and still am) rather disappointed that the Supreme didn't come with a back plate. Luckily I have access to certain things and I made my own. Like Martin I wouldn't think of mounting a block...
  21. Replies
    10,761
    Views
    2,780,403

    There is, it is just the angle of the photo.

    There is, it is just the angle of the photo.
  22. Replies
    10,761
    Views
    2,780,403

    Here is my work in progress. Still some stuff to...

    Here is my work in progress. Still some stuff to do like re-sleeve all the power supply leads. Antec does a piss poor job. I still have some wiring to do as well but it really doesn't effect the...
  23. Replies
    1
    Views
    427

    1/2" is 12.7mm. Either would work the 11.1mm...

    1/2" is 12.7mm. Either would work the 11.1mm (7/16") would just be harder to get over the barb.
  24. Replies
    83
    Views
    12,037

    Speaking of that, would you have any high detail...

    Speaking of that, would you have any high detail pics of the Iwaki RD-30 impeller?
  25. I wish I still had picks of my old "bong" cooler....

    I wish I still had picks of my old "bong" cooler. It was about 14' tall double walled to contain as much of the vapour as possible, very similarly to what zipdogso said. It used a four fan forced...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4