Search:

I am using H100. but not sure if the fan direction is working well for this case set up. both front and rear fans are pulling in air, radiator is mounted on top and exhausting air through radiator. I...

I just purchased a new rig using 3960x. The reason why i chose 3960x over 3930k was it was only at 125 usd over 3930k. It was an open box but unused. motherboard is gigabyte z79-up5.

While just...

I am running a back testing programs that tries many different combination.
to be honest it's not coded too efficiently. on one algorithm, it only uses 25% of each core and it takes hours to finish...

Thank you AMDforme, but AMD 8 cores are not true 8 cores? I have read a few postings from here and there now and I am confused.
If i can get something that's close to 3930K's performance at a lower...

I am referring to the chip i am currently using. I7-2600. Not even K.

Hi guys,
I have been away from the OC scene for quite some time... i was never too successful.
However, now there is a need for speed. Since I am currently using Intel 2600 on a gigabyte board,...

After messing around with the x58 - extreme for quite some time, I finally tried to install a sound card and a few other things..
i found there is just not enough space for any additional cards......

With F3 bios, there is no way to get it working on 200Bclk with 8X multi?
How about the current F4 beta BIOS?
thanks in advance!

I just got my rampage extreme.
Do you guys use the existing water cooling block or replace with the Air heatsink supplied?
thanks,
Jack

On this board, I can only max the FSB between 390-4000. I have tried upping the FSB voltage from +0.1v to +0.2v. It didn't help at all. what else can be wrong?

I am runing 4X1GB which maybe the...

thank you.

No I didn't disable either of the two. I will give it a try again.
Do you still have the check list and perhaps I will go thru mine too. thanks.
Jack

Currently I have Q6600, GIGABYTE P35-DQ6, transend 1066 ram.
all the overclocking is pretty mild on air. I have got the CPU up to 3.4G on air before.

Now the 4 GB RAM is new. I jsut got them...

Good point!
I am reading from the windows dialogue box (copying files). It says 3.78 MB/s

Recently I purchased a 3com Gigabit 5 port switch. On which, I have connected 2 PC'S AND 2 NAS.
All these components supposed can do gigabit with Turbo Frames up to 7k. I have set up each one of...

I just got it not long ago, so I still haven't started the oc yet. It's a G0 stepping.

so I can't turn it off to see if the system is stable at load with OC?

Also system temp sounds high doesn't it?

thx.
Jack

Hi Guys,
I haven't done OC'ing for a long time.
Last week, I decided to give it a go and bot an Intel with the following parts:
Gigabyte P35-DQ6
Intel Q6600
G. Skill
Windows Vista.

I have a...

I think I had a smilar problem before.
Back then, it was my Enermax PSU and the Expert board.
I had the same Enermax PSU with a SLI-DR, it worked fine.
I had the same Expert board with a TruPower...

i finally received mine. It was purchased from Newegg back in the end of November. My friend brought it over to HK since the egg doesn't ship internationally. I also ordered some TeamGroup yesterday...

So if I put tapes around the edges to seal it, that's all I will need to do? thanks!!

I just received my 146 CABYE 0540 FPMW today from a seller on ebay..
I also have a 150 CABGE 0532 at home I will have fun with this weekend....

Use plug the cable into the lower card! I had to find out the hard way.

I got one from newegg 2 wks ago. stepping CCBWE 0530. but I am stuck at 255X11 (2805Mhz).

I called the same shop and they told me they only had one. I called 3 wks ago and had a CABYE 0540 reserved for me, but I gave it up... now I had to order it form Japan.
the AMD distributor is crap...