131948131949
Type: Posts; User: wmaciv; Keyword(s):
Just an update after a few years... I now have 5 x ANS-9010 w/32GB each, 3 x RAID0 on ICH ports (6 channels), and one RAID0 on JMicron onboard controller. I also have a Hyperdrive 4 16GB on a...
Hye guys, have not posted in a long time; not in your league :). Just scored an new Areca 1222 for cheap and awaiting shipment. Any thoughts on two ANS-9010's in full RAID0 (4 banks of 16GB)? Will...
Bought a HD4 on eBay about two monts ago. Kinda neat to compare it to the 9010's. Two tiny, noisy little fans; 16GB of ECC DDR-400; a single ATA133 and/or the SATA-150 port. Transfer rates about...
From what I can tell, it's a 9010B with the 9010's added memory slots, i.e. single SATA port with the ability to support 8 memory sticks (vs. 6).
Thread has slowed a bit I see.... :) Still love my 9010... want more speed...
Just installed the 2.00 firmware... waht a pain to drop to "sata ide mode" just to upgrade the firmware. No...
My 32GB ANS-9010 FTW! Nothing even comes close for an OS/Temp file experience.
Well, I still can not run the ans-9010 for any length of time with the ACARD "homemade" ECC function enabled. I always get aan impending drive failure warning after a few startups and shutdowns, and...
Just burnt the new firmware... seems to have eliminated my problem with the ECC function causing corruption with my ICH9R, although, I also recently updated the BIOS on my Supermicro C2SBX. Anyway,...
My ANS-9010 is rev 3.1 hardware, not the newer 3.3 I wonder if the CF functionality is improved/fixed on the 3.3 hardware? I am pretty sour about the level of technical advice provided by ACARD...
First e-mail....
Hi,
1. For ANS-9010 8*4GB total 32GB,
Memory total capacity: unit:1024Byte
32GB=32*1024B*1024B*1024B=34,359,738,368Byte
ANS-9010 has ECC...
I still am convinced that the error on volume one (port 1) shown at boot time was COMPLETELY eliminated by jumpering the ECC function/RESERVED jumper. I'm not saying WHY it worked, but it fixed my...
I should have captured this in the previous post, but here goes...
When I remove the ECC function, and effectively enable "all" the memory, no matter what combination of RAM I use in what DIMM slot,...
Was having the devil's own time with the 9010 getting a corrupt volume on Port 1 (secondary port). Tried all sorts of RAM configs, still it would soon error on me either while running or between...
Josh1980, any experimentation with cluster size on your end? I used to fool with that on the Platypus Qikdrive8, and still not sure of the right answer. I have seen and a review where the smaller...
Ok, this is getting frustrating. Originally, for the first two weeks, I had 6 x 4GB sticks in a RAID0 config, with a (recommended) Transcend 133x 32GB CF card, and everything working as advertised. ...
Yeah, I love that program... so much better than Ghost... I bought a copy of Acronis TrueImage 9 a while back, and use it quite often, especially now with the 9010. I think everyone is thinking...
Here is an odd one.... I formerly had the 24GB of DDR2 backed up to a Transcend 32GB 133x CF card with no problem. Now, after installing the last 8GB of DDR2 for a total of 32GB, the "Backup to CF"...
Serra, you can set a jumper on the 9010 to allow all memory on one port.... of course at non-raid speed.
Wade
C2SBX w/Q6600 @ 3.0 gHz 1333 mHz FSB 2GB RAM
ANS-9010 has 24GB of ddr-2 800, and a 32mb Transcend CF card (133x)
After playing with the ACARD for about a week now, I pulled my two I-RAM box...
Josh (and whoever else)... Have 24 gig and a 32 gig flash card installed and running on the 9010 via ICH9R. Was a little trouble at first, but smoking now. Holy smokes, the flash card backup takes...
Josh, I only had time to pop the cover on mine before I left on my trip... The slots for the RAM looked pretty tightly spaced. Do you think many heat spreader equipped DIMMS are too big to place...
Josh, what kind of ram and where are you getting 4gb density sticks? Are you paying a premium, or have you found an inexpensive source? I would sure like to find some for my 9010 without spending...
My ANS-9010 just arrived this evening. I have to go out of town tomorrow morning for 10 days... argggghhhhh! Anyway, I don't have any memory for it yet, think I may go with 16 gigs of 4 x 4gb dimms...
From what you said earlier, I'm thinking of splurging for 2 4gb sticks at an unsavory cost, then finishing out the slots with 2gb sticks for a rough total of 20 gig, since 16 is cutting it a little...