Search:

Type: Posts; User: sabe; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. As long as you have achieved SOME compression, it...

    As long as you have achieved SOME compression, it will not leak at all.
  2. Ask them for a tracking number if available....

    Ask them for a tracking number if available. What's so hard? Is there some reason you don't believe what they say? They can just not sponsor you if they didn't want to give you free radiators.
  3. Replies
    26
    Views
    2,494

    I'm pretty sure its not connected correctly. The...

    I'm pretty sure its not connected correctly. The tubing from the res should be connected to the middle port of the pump top.
  4. Replies
    20
    Views
    2,178

    Makes you wonder how EK assembles it doesn't it?...

    Makes you wonder how EK assembles it doesn't it?

    These have always been tricky for me especially with non plexi blocks which doesn't even allow me a visual check.
  5. Replies
    6
    Views
    2,524

    1) Bad external o-ring. 2) Bad internal o-rings...

    1) Bad external o-ring.
    2) Bad internal o-rings for some rotaries and adapters.
    3) Compression fitting cutting the tubes when fully tightened.
    4) Putting the tubes on before tightening the base...
  6. A few bent fins won't matter as long as the...

    A few bent fins won't matter as long as the channels are fine.
  7. Replies
    20
    Views
    1,524

    I see where that user name comes from! :up:

    I see where that user name comes from! :up:
  8. Replies
    20
    Views
    1,524

    Use 60mm screws and thick plastic washers to...

    Use 60mm screws and thick plastic washers to space the fans 30mm away. The plastic washers now form a frame on which you can wrap sheet metal around.
  9. Replies
    21
    Views
    1,666

    Its just a little bit corroded which is very...

    Its just a little bit corroded which is very common for blocks with a copper base. A bit of vinegar or tomato paste soaked for a couple of minutes and cleaned off vigorously will get rid of it.
  10. Replies
    8
    Views
    771

    Merge loop 2 and 3.

    Merge loop 2 and 3.
  11. Replies
    29
    Views
    3,275

    Is your loop exposed to direct sunlight?

    Is your loop exposed to direct sunlight?
  12. If you're going high speed Yates then GTX is the...

    If you're going high speed Yates then GTX is the obvious choice. There is no dilemma here.
  13. Replies
    3
    Views
    573

    Feser Xchanger Series: 60mm Phobya G-changer...

    Feser Xchanger Series: 60mm
    Phobya G-changer Series: 60mm (closest match)
    XSPC RX Series: 63mm
    HWLabs GTX Series: 54mm
    HWLabs SR-1 Series: 55.7mm (Shape is quite different from the XChangers...
  14. From experience, it happens more often on loops...

    From experience, it happens more often on loops with blocks that have injector plates. Sometimes it gets so bad there is no flow at all, only gunk on the injector plates.
  15. Replies
    10
    Views
    1,320

    That would be at least 3-4 months ago.

    That would be at least 3-4 months ago.
  16. Replies
    41
    Views
    9,879

    RX360 is way ahead of the RS360 when it comes to...

    RX360 is way ahead of the RS360 when it comes to cooling performance especially with decent fans. I know the HAF X has no problems fitting a RX360 up top, not sure about the HAF 932 so that's...
  17. Replies
    41
    Views
    9,879

    Distilled water with silver killcoils or pt-nuke...

    Distilled water with silver killcoils or pt-nuke :)
  18. Replies
    27
    Views
    4,488

    Koolance and MIPS have those for sometime now...

    Koolance and MIPS have those for sometime now actually.
  19. Replies
    27
    Views
    4,488

    Because for Dominators you can just unscrew the...

    Because for Dominators you can just unscrew the stock fins on top and slap the blocks on top of it. For other types of ram, you need to make an adapter to actually goes downwards at a 90 degree angle...
  20. Don't forget the new XSPC universal GPU block too!

    Don't forget the new XSPC universal GPU block too!
  21. Replies
    5
    Views
    894

    Looks interesting for the price, are the...

    Looks interesting for the price, are the intlet/outlet tapped? Can't really tell from the blown highlights.
  22. Thats the opposite of what he said.

    Thats the opposite of what he said.
  23. Replies
    9
    Views
    814

    How can you expect temps to be below ambient...

    How can you expect temps to be below ambient unless you have some sort of a chiller? 72F is over 22C.
  24. Replies
    580
    Views
    102,337

    Holy moses guys!

    Holy moses guys!
  25. Replies
    171
    Views
    29,132

    The link on the Swiftech home page for the pump...

    The link on the Swiftech home page for the pump is incorrect, here is the page: http://www.swiftnets.com/products/MCP35X.asp
Results 1 to 25 of 260
Page 1 of 11 1 2 3 4