That is quite possible but the problem with that would be my ram speed. Now for 4.1 only need 170 bclock and a ram speed to 1700 with a 23 multi it would take a 178 bclock and unless I changed the...
Type: Posts; User: Ancient_1; Keyword(s):
That is quite possible but the problem with that would be my ram speed. Now for 4.1 only need 170 bclock and a ram speed to 1700 with a 23 multi it would take a 178 bclock and unless I changed the...
I just switched out my 920/DFI for a R3F and a 950. I need 1.33vtt and 1.28 v-core for 170*24 (4.09), 171*24 is unstable at the same voltages. I did a short check to see my temps at 175*24 with...
I run mine both ways depending on what I am doing. The main use of my system is trans coding HDTV to Xvid (6~10hrs a day) and occasionally x264 (5~6hrs a week). I run with all power saving features...
I believe you want EIST DISABLED, CxE ENABLED, PPM ENABLED, TURBO ENABLED and in windows you want to set the power scheme to performance. Setting the power scheme is important, also the correct bios...
That is the message you get after a successful bios flash. Are you sure it didn't flash?
I guess W7 doesn't like 3g of ram. other than the mem score about what I expected.
96883
I have been through this and what unclewebb says is true. once you set it to portable/laptop the readings will be right in those apps and the muti bounce will become more stable.
Here is what my...
I see you are on a 64bit OS I would guess that is what makes uor results quite different. If I had a 64bit OS installed I would of done it all there, but I have driver issues with my capture cards...
Thanx unclewebb I never thought that is what was needed. I knew that there were settings in Vista but since there were no similar in XP I never thought I would have to list it as a Portable/Laptop to...
Here is my results from CB 10 and POV @ 3200 with HT off done in XP32 which should be a good comparison to your PII.
CS 10 920@3200 HT @ Turbo off...
Here are my results from my 920 with HT and Turbo disabled (I have screen shots if needed).
XP32 920@2660
All 4 cores
CPU time used: kernel 0.41 seconds, user 416.31 seconds, total 416.72...
The Tech Report did on the 965 when they did their review of the new PII's
I have found that Cpu-Z 1.5 will not read the multi change on my DFI 920 setup correctly.
I have found that Core Temp (a little erratic tho), Cpu-tweaker, and Everest will tho.
Idle...
I had 2 2.4c that would both do over 3.5 and the main one would bench 3dmark2k1 at 305+ fsb and I think it was my MB that was the limiting factor since it only needed 1.6v to do it (no increase in...
I would say the 1c7 max3. I had both the p4c800 and the max3. The p4c topped out around 293 fsb while the max3 would bench at 307 and run 24/7 at 300. Also on most benchmarks the max3 was slightly...
Here is mine on a DFI P35.
I could not set the performance level to 7 with the cas set to 5, I tried with memset and got a hard lock and with bios I had to clear cmos.
Since I couldn't get cas 5 to...
Results from my DFI LP LT P35 T2R and 8400 @ 4.2
Results for x264.exe v0.58.747
encoded 1442 frames, 46.21 fps, 3905.08 kb/s
encoded 1442 frames, 48.07 fps, 3905.08 kb/s
encoded 1442 frames,...
It seems to me that its the quad cores that require a bump in voltages other than vcore and vdim to run 450+.
I have no problem running 24/7 @ 467 with my 8400 with only mem and cpu voltages over...
I think my 745 is a decent chip also.I am just trying to decide if I want to go over 1.3 (1.34) 24/7
http://webpages.charter.net/chew_toy/DFI8400/O461.PNG
or under 1.3 (1.28)
...
ThatGuy16
I adjusted my cpu temp offset in bios (+13) to basically match my Core Temp load readings. Now in Windows Smart Gaurdian is usually within 1~2° of Core Temp load readings and will keep...
Here are the specs of what I just put together Friday. I will probably get a different vid card in the next month or two but as is will do just what you want.
DFI LP LT P35 T2R
E8400 Wolfdale...
I was Class 69
I would contact Cathar. If I remember correctly there was a problem with the o-ring groove on some of the early G5s which could cause leaking.
As far as the screws go I see someone has stripped...
Series is almost always best (only time I could see parrallel better would be in a really low restriction setup like a single maze4 setup). 3A would be quite marginal for two running long term I...
The rev2 mcp600 has a serial# that starts with an S. You should see some improvement running two in series but it will be small but will add protection from a single pump failing.