gtx480 w/ push/pull fans and shrouds FTW!
Type: Posts; User: kahuna321; Keyword(s):
gtx480 w/ push/pull fans and shrouds FTW!
I use Sythe Ultra Kaze 2000's in push/pull with shrouds. With a fan controller I usually run them at 1200, but when needed in summer or extended gaming sessions I spin them up higher. I get a +3...
in a few days the asus 1215 is coming out- wait for it...
check to make sure the backside of your motherboard is not making contact with the case and causing a short. I have been braindead while building before and accidentally screwed in a post in the...
I use an external rad box for several reasons. First, it allows me to easily maintain the setup. Secondly it fits conveniently behind the desk, removing fan noise from the user area. I prefer tech...
Running feasibilty on using 3/4" solid copper pipe for main and manifolds with 6 lines of 3/8" 60' soft copper coils loosely looped between manifolds for cooling. Greater surface area for cooling...
I am surprised noone has mentioned the Mionix Naos 5000. As an extreme gamer I spend hours at a time using the mouse, and among most high end products the sensor quality is excellent so the only...
Thanks
What about 2 RD30's in series? They are only to drive the geo loop through the exchangers, not the pc's. They are on seperate loop from exchanger to pc.
I am in the initial planning stages of a large geothermal cooling loop. I am planning on using this to cool 2 seperate pc's.
I plan on using over 300 feet of copper pipe buried 36" below ground...
already wcing nb, asking about mosfets and vregs
should I w/c both, or just one- and which one? I have block for both
thanks
+1 for the enermax magna 120's- quiet, great cfm and pressure- and a deal at directron for 12.99 w/ great shipping costs ( reviews here...
never even thought of router, and i have a bosch too. will check out bits too.
thx for link!
thanks for your suggestion, i'll put the skillsaw away. used dremel lots, but have trouble with long cuts in metal. looking at diamond cutoff wheels for it now, though. regular metal cutting disc...
I am starting a tech station build, working with a Lian Li removeable motherboard tray http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=210&products_id=3387. I need to...
these are the 1950 rpm models, not the 2600 models. Still good though, but "only" 77 cfm/32db instead of 39db/102cfm
tried your settings- no post. tried moving from there a little but still no post. this cpu/mb dont seem to like a lot of volts
still trying...
tyvm
finally got the w/c set up and running. got a quick and easy bump to 4400mhz, need suggestions to get 4500+
this is my setup:
ga ep45 ud3r f9
q9650 vid 1.1875
g.skill lv 9600 4x2g
corsair...
finally got the w/c set up and running. got a quick and easy bump to 4400mhz, need suggestions to get 4500+
this is my setup:
ga ep45 ud3r f9
q9650 vid 1.1875
g.skill lv 9600 4x2g
corsair...
sidetracked atm- not happy with new w/c setup cpu temps. running enzo sapphire cpu and nb blocks only, w/ gtx480 and 8 uk fans, 3.25 pump w/ xspc res/top, 1/2" tygon and all high flow fittings. water...
just the rad, and everything will be sealed to the ductwork. one intake, one exhaust. gonna start running temp studies next few days as it will be close to max temps in our area. as long as I can get...
what I am talking about souns alot easier than what I've read about chillboxes so far. Some sheetmetal and ductwork to get cool air and exhaust the hot. Should lower noise, and if sealed wont...
so lower vid overclocks with lower voltages, but is hotter doing that than higher vid cpus that presumable take even higher voltages to overclock? So I should look for higher vid cpus?
thx
just thought of another hair- brained idea- running heating ductwork from intake fans of w/c setup to crawlspace under house- always much cooler air there. and running ehaust air outside the house,...
out of curiousity, what VID should I look for when picking out another cpu?
I currently run a q9650 EO with a VID of 1.1875- is that good?
or is there even a relationship between VID and...