Great review SKYMTL, will you be doing any SLI results?
Type: Posts; User: Roch; Keyword(s):
Great review SKYMTL, will you be doing any SLI results?
New Drivers.
http://www.nvidia.com/object/win7-winvista-64bit-301.10-whql-driver.html
I'm using an old first gen raptor as an emergency drive now so I'll leave the SSD's out of the machine and see if they'll revive themselves tomorrow.
The PCIE frequency is set to 100 in BIOS.
...
Thanks for the replies guys, I appreciate it. I can't actually see the drives in bios so I don't think I can flash to a newer firmware. I reset cmos before I swapped boards so I think that's ruled...
My PC crashed recently (it's previously been rock solid since November when I last reformatted) and after a forced restart I couldn't get past the "Detecting SATA 2" during POST, where it froze.
...
My PC crashed yesterday (it's previously been rock solid since November when I last reformatted) and after a forced restart I couldn't get past the "Detecting SATA 2" during POST, where it froze.
...
How do you mount the The aquaero 5 LT in a case? Does it fit somehow behind a 5.25 blanking plate?
244w I believe.
How do these look?
http://i234.photobucket.com/albums/ee12/markrochester/crysis256.png
http://i234.photobucket.com/albums/ee12/markrochester/3dmark11.png
900/1800/2200/1125mv.
Thanks! Will give it a go now. :up:
I got 2 Palit 580s installed, the stock vid is 1000mv. I can only get to 850core (memory not touched) at 1100mv, anything higher and it crashes Heaven 2.1. Any advice? This is in a case, stock...
I killed a PSU and motherboard trying to run 2 overclocked 470's on an 850w PSU so I wouldn't think you'd be able to run 3 on a 950w, especially if you're overclocking.
My 470's at 840.
http://i234.photobucket.com/albums/ee12/markrochester/840core2.jpg
I had fairly good results with the MK13s, they like lots of fans to make them shine though and the supplied heatsinks aren't great, I replaced mine with enzotech copper ones. The Gelid seems to be...
Fitted a new motherboard, all seems fine now. This has been an expensive week :(. Still, at least i've got the weekend to properly see how far I can get the cards to clock, does anyone know of any...
Surrey? That's my neck of the woods, i'll be looking overhead, fire extinguisher at hand. :D
I fitted my replacement PSU last night. I think the mobo may be damaged. Windows was corrupted and so I reinstalled Win7 and had another go at overclocking. I managed 850 core on both cards at 1087mv...
It was a Coolermaster CM850, not the greatest out there but pretty good. I thought it would have handled the load, I suppose it just goes to show the power these things use overvolted. I've ordered...
http://i234.photobucket.com/albums/ee12/markrochester/IMG_0794.jpg
Fitted and running! Max combustor temp of 47 for the top card and 42 for the bottom one. A problem however, I seem to have a...
Thanks Pilsy, that's sorted it. :clap: The water noise has completely gone and the pumps much quieter. I'm mounting the rad with Lian Li Rad Brackets so I might try and rig something else up to...
OK, so I spent yesterday afternoon putting the loop together. It all went in (although a bit of a squeeze to get it all in) and I've left it over night to leak test, 12 hours so far.
what's...
Gabe has confirmed they're compatible, thanks Gabe!
Thanks, will stick to my plan then.
Thanks for the advice, I didn't realise that. The reason for the way i've set it up is purely the shortest and neatest tubing route, will the temps be affected greatly or I we talking a couple of...
Thanks Wesley, i've fired off an email to Swiftech support.
What I ideally would have liked were Matt black fittings throughout and a single correct length Matt black D-Plug for each of the SLI fittings, however, no one in the UK had all the bitspower...