Any updates..?
Type: Posts; User: Rub87; Keyword(s):
Any updates..?
Vtt should always be around 1/2 of Vdimm..
The problem is when you connect the 3.3v wire directly to vdimm you have a chance the Vtt won't track and you'll get poor results..
I built myself a...
Hi,
FINALLY it happened, and I resoldered that biatch, I didn't test the board yet, but the mosfet seems pretty good..
So I just sanded aaway the moset of the dirt on the board and mosfet, then...
Hi, my BH-5 does around 265-270 on lanparty..
Is ist normal that if I run the mem for exempla @ the 7:10 divider it is able to archive better results then when running 1:1 with the same timings?
Here ya go...
Nice going :D
Yeah, that's a pain in the ass... Maybe you just burnt the vcore mosfet, or is the vcore still allright when you fire up the system..?
I always connect multimeter to the cap and use a 15-turn...
Lol, and what cooling were you usig at that moment..? I hope nothing less than phase change..
What's the use of putting the molex connecter that way..?
Lol didn't test, as you see, the card is in my backup rig.. stock cooler is on the card so I don't oc her.. It's more a backup card..
Yeah, thats normal, on those card you never get artifacts due the core, only framedrops and if you go a little higher the screen freezes..
You don't have to look anymore, the diagram in the...
Yeah, or the chip is bad or the board is bad or I'm too stuped to use DCDDR..
But I really love the board, does 400fsb out of the box...
And the cpu, I don't know much about A64's, this is my...
Hi,
Got myself a DFI lanparty UT Ultra-D, Venice 3500+, a tagen 580w psu and X800XL..
I only have one problem with this setup and that's that If I put memory in one of the 2 lower dimms the...
Thanks,
I'll get some smd grabbers and check it out..
Prommy is mounted succesful, cpu does around 3.2, and atm I'm running primy at 390 HTT, BUT, for some fukkin reason I am not able to use...
Nope, I'll try it when have time, atm I'm building new setup and have some troubles fitting the prommy on the dfi lanparty ultra-d
OCZ DDR booster VDroop and stabilizing mods..
http://www.xtremesystems.org/forums/showthread.php?t=50444&page=1&pp=25
Regular GF's and Ti ones have different cores... if Ti and a regular GF are at the same clocks, then the Ti will perform better..
Depends on whats wrong with the card, the easiest problem should...
Without pelt was around 225-230 if I remember it right..
I don't see why another ground point could help.. as we are working with high resitance VR's, so we have very litlle current flowing trough...
Same here, The card used to have pelt setup.. ran 240mhz on lowered vcore. I only came whilme later after it that the mod was actually lowering the core voltage .. but with that time I had removed...
Hmm, if you are sure that it is vdimm your software is reading way off.. wich is very possible, never trust software radings..
Under dimm 3 you see a 8-pin chip, the 2 upper left pins are vdimm.. 2 upper right are vbt/vtt
NDP603AL
Hmm, be carefull to not make the wires too long, this will cause a non stable working.. keep them as short as possible, especially the gate one...
Why don't use one big decent mosfet, like the BTS240 or something..?
There you go, let me know if you need more specifik areas..