Search:

I would say either A or D, but ultimately the order has little effect on the performance of your loop. Flow rate has more of an effect on how well your loop cools than the order of your components....

I'm putting together a couple of new loops using the full copper Alphacool Nexxos radiators and I've read in a few forums that Alphacool radiators need alot of cleaning prior to use. Most of these...

Bought the pump in April of 2010 so it's only a 1 1/2 years old.

Like I mentioned above, if I spin the impeller by hand I can get it to run but it won't start on its own. Any way to check voltages...

I figured they were all the same. I'm guessing the specs vary because of creative calculating for marketing purposes.

Whatever the case I've already got 2 PMP-400's being overnighted. Now I will...

Well looks like My pump died. When I teurned on my machine today the pump wouldn't start. I drained the loop and pulled it (water was clean, no trash) and it looks OK but it won't spin unless I give...

My flow has been pretty consistant and my pumps have always been about 4800 RPM. Thhe other day I noticed my GPU loop has dropped about .8 LPM and my pump RPM to 3990 - 4020 or about 1000 RPM.
...

I DID get the new EN versions. I almost didn't but after spotting a post about the old ones I did a little research. I then realized the vendor(who will remain unamed) I was about to buy from had old...

Temps haven't broken 60c under full load



Actually I replaced the flow meter when I installed the 580 blocks. The previous flow meter was doing the same thing, "sticking", but I think I killed...

Yep, my temps have been fine, even under load. That's why I haven't been terribly concerned, However, I found red trash in my first 470 block(They were in series) when I cleaned them. I haven't done...

No, now I am not sure, at the time I thought I was. My other loop has a 360 Rad also but I haven't had any issues with it.



Just PC Nuke in distilled water.

I recently got a pair of EVGA 3g GTX 580's and EK water blocks. The are replacing 3x GTX470's and Koolance water blocks.

My problem started with the 470's and the Koolance blocks (I have a...

I've got Koolance on my 470's right now and I'm using the connectors you listed, however those connectors don't provide parallel water flow. My three cards are in series and I have to clean out the...

Just got a pair of EVGA GTX580 3g cards and I'm undecided as to what waterblocks to get for them. I'm looking for some that will take a bridge and parrallel flow so The EK and Heatkiller blocks are...

Just got a pair of EVGA GTX580 3g cards and I'm undecided as to what waterblocks to get for them. I'm looking for some that will take a bridge and parrallel flow so The EK and Heatkiller blocks are...

I'm trying to decide which one to get, either the ASUS Direct CU II or an EVGA GTX580. I'll be getting two of them to start (Maybe adding a third later), and I'll be Water Cooling them also. I've...

North american distributors? Preferrably US and carries the full line.

If I want to control two loops and monitor two flow meters whats the best configuration.
Both loops are the same and as follows.
3x fans
1 Flowmeter (FM17N)
Laing DDC 3.25
1 inline temp sensor...

Cleaned out the blocks and it seemed to improve the flow. My flow meter stopped working(I think). I pulled my TMS200 and put my Tban stuff back in, except for the mCubed Flowmeters. Well the...

Maybe, but I've been wanting to upgrade my CPU for awhile and I haven't had great luck getting this 920 above 4ghz on this R3F. It did fine on my P6T however but I did need to run my vcore a little...

and BTW I really appreciate all the input I get from from everyone on this forum :up:.

Yeah, I'll go ahead and stick with the 470's untill at least the revised 590's hit, I guess I felt a little burned when the 500 series hit without seeing a dual gpu 400 series card.

I'm starting...

So in other words no overclocking?

I've heard that there is going to be a revision of the 590 in June, could this be one of the things that gets "revised".

Also I'm not really fond of gaming on...

Not sure I follow you about "blow up"

At the moment just one 23" 1920x1080 and a 17" I use for gadgets, AID64 OSD monitoring, etc... but am considering a second 23" for a total of 3 monitors.


This was the first thing I considered...

Just looking for some opinions here. I've been contenmplating on upgrading my 3 GTX470's to the GTX500 series and WCing them(or it). I'm especially looking at a GTX590.

I've looked at a couple of...