AWESOME, can't wait for your post!
Printable View
how heat sensitive are the resisotrs you solder to in order to read voltages?
So anyone with the mod done have any results clock-wise? I see a couple of people who have watercooling/aftermarket air-cooling hitting upward of 770-800mhz core without the mod, I'm darn curious how high these will go with more voltage.
:eek2:
Will a VF-900cu be able to handle the wrath of G92?
stock/vmodded...either? no? maybe?
Stock, pretty well but it will probably max out... vmodded, not so sure :(.
Hey, no 500ohm VRs around like I thought.
Stock metered voltages on SSC are vGPU-1.107 at desktop, 1.137 loaded; vMem-1.995.
With MCW-60 can run 800mhz core at 29-30C loaded.
Sorry, out of time, pics ect to follow this weekend.
I will probably just order a few from McMaster.
Someone asked about the SSC bios, and I think it was in this thread, so I attached it. The voltage identifier is 1.05 like the normal 8800. However, my vGPU and vMem are higher than normal.
Unfortunately this card aint mine, just did a quick research so to please the OC-community. No results, but I can tell you that I could increase to 1,2VGPU. Anyway, XS counts enough people owning such card, it will not take too long before those cards are running at 1GHz I suppose :)
Didn't picture it, you will have to take me on my word here :(
Vsen+ is the pin marked below:
http://i30.photobucket.com/albums/c3...bbbbbq5mod.jpg
so it only works to pin right??
No, all these spots work.
If not, there's something wrong with the VR/other equipment.
http://www.xtremesystems.org/forums/...1&d=1193851215
Heat is a killer on my card at least. On the first 3D '06 run I hit 83c. I pulled off the HSF and applied AS5, got down to 75c on the second run. I almost burnt my finger on the heatsink though. I guess those NVIDIA engineers who have been saying "We're good to 100c" are pushing it a bit here.
Needless to say, the card was very stable at 700mhz core, and ran through a '06 pass as high as 733. I couldn't get much more out of it without doing better cooling and maybe this volt-mod. We'll just have to see how the cores do with about 1.2v.
i have no heat issues what so ever with my stock cooler, even overclocked >770/1800/1000. I think my last 3dmark run peaked at 72°C. The only thing you have to do to keep the heat down is max the fan @100%... of course it sounds like a hair dryer then, but i only do that for 3dmark runs.
edit: sorry to go off topic (volt mods)
The problem is definitely the Overvolt Protection. The 8600gt/gts can hit 1000 core with volt mod's and no OVP.
lets see a shot of someones modded card.
Well, are there any results yet?
yes i see its working
last night i tryed but to no luck
i seen today that my ground wire was off.
testing 1.29 load now
thank you from me and the others who dont thank but use
best wishes
cow
So what are you all hitting with increased volts?
well i just had it at 1.55 3d and 3c
no blacksreen and i did not get the clocks i thuoght i might hit only benchmark stable at 810-825.
but its only been a few hrs
i'll start slow and backdown for 24/7 to 1.28 that did not effect temps much but gained me 50mgz on core
i just play around not going for the kill to early
how much drop and droop are you seeing
1.55V :shocked: LOL
what cooling are you on