The ULTIMATE ASUS CT-479 Adapter Modifications...You want MORE...GET IT...

Printable View

Show 100 post(s) from this thread on one page

12-05-2005, 05:59 PM
hipro5

The ULTIMATE ASUS CT-479 Adapter Modifications...You want MORE...GET IT...

Well, I'll try to explain some things to you in simple words...:)

REMEMBER THIS: DOTHAN CPU's can do MORE BUT ASUS CT-479 adapter, just DOESN'T let them...

Now...I have a DOTHAN 740 CPU (not mine) in my hands that could do 3D Benchable on air with the ASUS adapter's heatsink, MAX 2700MHz...OK....
Put it into a prommie and it did MAX 3074MHz 3D and other stuff benchable...I could run a Super-Pi 32M @ 3074MHz also...Everything over 3100MHz was NO GO...Freezings and things like that....Also it couldn't handle over 1.575VCore...:(

I said to my self: "HOW the hek is it possible to go up to 3100MHz MAX and NOT EVEN 1MHz fsb more than that!!......Do this reminds you something??...:D :stick:

Time for reading and afterwards modding....:)

I downloaded Intel's datasheets for Dothan CPU's and take a good look on them....

BINGO

ASUS has done a BIG mistake on the design of the CT-479 adapter as for US Overclockers...
Well not really a mistake BUT they didn't have "US" in mind when they designed the adapter...;)
They have designed in for everyone out there....;)

Modding the adapter I gained:

DOTHAN 740 BEFORE Mods
Benchable 2700MHz on air with the default ASUS heatsink
Benchable 3074MHz in a Prommie

DOTHAN 740 AFTER the Mods
Benchable 2830MHz on air with the default ASUS heatsink
Benchable 3224MHz in a Prommie:D :toast:

PLUS I even HAVEN'T finished searching for MORE mods or for more (beeeeepppp - SORRY NOT now)...:D

At this point, I'm uploading you the "simple mods" that can be done....:)

UNFORTUNATELY for you, I will NOT upload the "ULTIMATE Mod" for the time been coz I'm preparing my stuff for some heavy benching in one of the following days....

BUT I promise you that as soon as I finish my benching, I'll upload AND the "ULTIMATE Mod" of the ASUS CT-479 adapter...and even more...:D ;)

BAD thing is that when playing around with the mods, I blow up one of my ASUS P4C800E-Deluxe mobo....Now I have to repair it - when I find some time to do so:(

Let's get started...:)

As I ALWAYS say: "FILTER EVERYTHING"...:D

This photo shows the adapter ripped off so as to find out where the lines underneath the socket goes...:)

http://www.thelab.gr/images/Hipro5/D...pped_1_jpg.jpg

This one shows the other side of the adapter - ripped off as well....:D

http://www.thelab.gr/images/Hipro5/D...pped_2_jpg.jpg

Now....Let's do some moding...:)

http://www.thelab.gr/images/Hipro5/D...dded_1_jpg.jpg

In the above photo you can see TWO electrolytic capacitors....One is a normal 100uF/16V and the other one is an SMD 47uF/16V tantalum - you can solder a regular one also...These two are for the "incoming" 12Volts line...

http://www.thelab.gr/images/Hipro5/D...dded_2_jpg.jpg

In the above photo you can see some SMD 1uF/63V ceramic capacitors - you can put 100nF/63V ceramic SMD capacitors if you don't find 1uF/63V...As you can see, there is a BLACK SMD 22uF/10V tantalum capacitor as well...This one AND the two on the left of it, are for the VCore of the DOTHAN - in simple words and not to confuse you....;) :)

The uper left circled missing electrolytic capacitor, is the one we have soldered BELOW the adapter...;)

If you have anything to ask - exept for the "ULTIMATE Mod" - Please do....

Final words are:
Your DOTHAN CPU's are going to kick some "green" butts for SURE in a few days....;) :D :toast:

TO BE CONTINUED......
12-05-2005, 06:28 PM
Mr. Tinker

whoa. My request to you is simple, HiPro: NEVER LEAVE THE OVERCLOCKING COMMUNITY.
12-05-2005, 06:49 PM
Frozendeath

Nice job with this, I can't wait to see the ultimate guide. As a dothan owner I can't thank you enough, when I get my p4gd1 I will definately mod my ct-479 :slobber:
12-05-2005, 06:54 PM
IYP

wow, great work man, cant wait to see what this brings all and all, will be amazing as always from you :)
12-05-2005, 07:00 PM
[XC] moddolicous

Hmm, if the japs didnt know this, is it possible that their dothan still have something left?? Maybe a 4.5ghz SPI run? BTW, hipro, cant wait for your LN2 run. Hopefully we'll see some insane results.
12-05-2005, 07:06 PM
hipro5

Thanks guys....:toast:

Yes I think that the Japanease guys could do about......200 - 300MHz MORE......;) :D

EDIT: I'm still waiting for my ASUS P4GD1 mobos..... :(
12-05-2005, 07:18 PM
rcchong

and there you rOw again :-)
btw it's quite hard to find your defination of uLtimate mode.

(it's about time someone look into the 479....)
12-05-2005, 07:31 PM
Movieman

reading this made my night!:D
12-05-2005, 07:57 PM
STEvil

might try two tantalum caps in parallel where you put the one... and beefing up the traces so they can carry more current? :D
12-05-2005, 08:14 PM
Gautam

Man hurry up with those benchies so you can let us all know about this "ultimate mod", lol.

How much would these simple ones help, MHz-wise?
12-05-2005, 08:15 PM
runmc

You sure added alot of stuff to the adaptor. Is it possible for you to label each part you added so we know exactly what is what?

It's hard to see where you attached three of the components. Can you point an arrow to each solder point before the component is added?:D

You asked if we had any questions:)
12-05-2005, 08:20 PM
Vapor

And bookmarked....Hipro, you are the man.

now I just gotta get my soldering skills up to snuff
12-05-2005, 08:26 PM
CrazyXP1700

looks like im gonna be moving over to a dothan :D

i was looking for mods for the adapter... didn't find any so far

EVERYTHING's GOTTA BE MODDED!
12-05-2005, 09:53 PM
STEvil

Quote:

Originally Posted by Gautam

How much would these simple ones help, MHz-wise?

seems to be 100-300mhz if you read the posts :stick:
12-05-2005, 10:14 PM
2fink

Sticky?! :toast:
12-05-2005, 11:04 PM
mrlobber

:slobber:

Need... to... practice... soldering... skills... ASAP :D
12-05-2005, 11:25 PM
Unseen

how about making a new adapter? Nice job as always...
12-06-2005, 02:59 AM
hipro5

Quote:

Originally Posted by STEvil

might try two tantalum caps in parallel where you put the one... and beefing up the traces so they can carry more current? :D

No need for that coz the adaptor doesn't draw that much current.....;)

Most current(mA) is drown through the Big Mos-Fet which stabilizes the Voltage at 3.3Volts sharp for the rest of the circuit to work...

Off topic......With this new version of Vbulleting I can finaly "quote" someone.....Before I just couldn't....:D

Quote:

Originally Posted by Gautam

Man hurry up with those benchies so you can let us all know about this "ultimate mod", lol.

How much would these simple ones help, MHz-wise?

I have gained about ~130MHz+ with the default ASUS heatsink and ~160MHz+ on phase change so far.....I think it could easily be gained ~200MHz on air if I search it a bit more......;)

I bet that the DOTHANS could boot over than the 230 - 250MHz fsb which was the limit to boot till now......I'll have to check this out so as to be sure - forgot it - ....:)

Quote:

Originally Posted by runmc

You sure added alot of stuff to the adaptor. Is it possible for you to label each part you added so we know exactly what is what?

It's hard to see where you attached three of the components. Can you point an arrow to each solder point before the component is added?:D

You asked if we had any questions:)

Gee ......Those are a lot of questions.....:D

OK..I'll do so.....:)

Quote:

Originally Posted by CrazyXP1700

EVERYTHING's GOTTA BE MODDED!

Yes....That's EXACLY my opinion too.....:D

Only the Maximizer doesn't need any mods coz is already full moded....:D

Quote:

Originally Posted by Unseen

how about making a new adapter? Nice job as always...

Thanks Chris....:toast:

Making a new adapter even a socket 775 one, I need TWO things.....a. licence contract with ASUS which has the rights for Patent Pending and b. a motherboard company who can back me up with bios updates so as mobos to "recognise" the DOTHAN CPU's coz I'm a "harware man" so I need a "software man" as well....;)

Quote:

Originally Posted by mrlobber

:slobber:

Need... to... practice... soldering... skills... ASAP :D

Yes I think you should.....;) :D

EDIT: I deleted my posts coz they where too many and I quoted all quotes and answers in one post.....That's better.....:D
12-06-2005, 04:31 AM
skane

nice hipro, do you think you could mod some more adapters and maybe sell one of them to me?? my soldering skills are pretty much zero, so i cant do it myself.
12-06-2005, 04:38 AM
hipro5

Quote:

Originally Posted by skane

nice hipro, do you think you could mod some more adapters and maybe sell one of them to me?? my soldering skills are pretty much zero, so i cant do it myself.

There are guys all over the world that can do mods.....Where do you live?...
12-06-2005, 04:46 AM
leejsmith

Hipro5,

can you explain the mods on the backside of the ct-479 the picture is dark and i am not sure what to do.

edit: now i had looked at it for few more times i undertand.

why do yo have the fsb jumpers circled ?
12-06-2005, 04:50 AM
hipro5

Quote:

Originally Posted by leejsmith

Hipro5,

can you explain the mods on the backside of the ct-479 the picture is dark and i am not sure what to do.

Yes, I'll try to upload some more clearer photos....
12-06-2005, 05:23 AM
Vitality

Wow that looks great! :toast:
Im really waiting for some more info what u exactly did. Maybe i will try that later then. That is just so GREAT STUFF! :woot:
12-06-2005, 05:30 AM
persivore

Looking great as always, Hipro. Thread stuck :)
12-06-2005, 05:55 AM
skane

Quote:

Originally Posted by hipro5

There are guys all over the world that can do mods.....Where do you live?...

im living in belgium, so it wouldnt be that expensive to send it over.
unless someone else here can/want to do that mod and lives closer...

Show 100 post(s) from this thread on one page