anybody willing to order for me?
anybody willing to order for me?
Very nice result mate! Thanks a lot. You should try also @cold boot.
Bye.
Quote:
Originally Posted by LagunaX
@Punisher! - no problems with cold boot with my board. Disconnected the power for 15 min and then plugged back in and booted up just fine. The earlier versions of Asus P67 boards did have a cold boot problem but was fixed by a B3 bios revision and/or "enable wakeup from PCI-E" in the bios. Also turned it on first thing in the morning (it's winter time) in a cold office this morning and was just fine too. Did my 1st hour Prime95 first thing this morning (cold boot) and the second 2 hr Prime95 right after the disconnect.
@Alex Ro - well tried 1.5v and 1.55v - both BSOD'ed around 45 min on Prime95 blend.
However...here is 2 hours Prime95 blend @ 1.6v vdimm @ 9-10-10-28 1T DDR3 2133 at the same 4.8ghz 4C8T :)
http://i246.photobucket.com/albums/g...msungLV16v.jpg
http://i246.photobucket.com/albums/g...msungLV16v.jpg
They just got a dollar cheaper @ the Egg and I guess these are keepers! :up:
15min. off is not a cold boot. 8 houres off is a cold boot here :D.
Well guys I have ordered 3x4g M378B5273DH0-CH9 . This are not the low profile version. I will update with the X58 platform results and see if they perform as good as with the x79 platform :)
Cool. I am curious about P55 myself.
Very nice. Do the ICs get hot after the test at 1.6V? Would you mind running these through LinPack as well?Quote:
Originally Posted by LagunaX
Already did 2 hours of Prime95 which I consider a better test than linX/LinPack for stability but that being said linX usually will pick up any errors in the first 5 runs:
http://i246.photobucket.com/albums/g...amsunglinX.jpg
http://i246.photobucket.com/albums/g...amsunglinX.jpg
IC's seemed fine but you'd be hard pressed to find a sized to fit sleeve heatspeader I think for these low profile kits - makes me think of the old Zalman blue ramsinks that came with their vga cooling kits!
http://images17.newegg.com/is/image/...20-S01?$S300W$
Samsung 2x 4GB 30nm Low Profile, Not bad
Prime95 Blend 8hrs @ 1960Mhz 9-9-9-27 1,47V :eek:
http://i41.tinypic.com/2cyftch.jpg
http://i40.tinypic.com/15enp1.jpg
Wow, so good, even if Blend tests only 1600MB, you should choose "Blend" and then "Custom" putting the right amount of RAM to be addressed (example: 7000MB). Click on my signature for the result.
Nice results Barr3l Rid3r!
I am sorry, you are totally wrong:Quote:
Originally Posted by Barr3l Rid3r
http://digilander.libero.it/m4puni/prime_main_1.jpg
MEMORY TO USE (MB): 1600 so it uses 1600mb (first mistake)
Second mistake is that MEMORY TO USE has nothing to do with larger blocks size.
You should actually test as I have just told you for better test with respect to memory stability.
Blend, then custom and put 7000 instead of 1600.
Happy to report these modules are working very well on the X58 platform for me. You can hardly see the ram when they're installed they are sooooo small. Modules are running 2Ghz 1.5V. at 10 11 10 31. Currently at work but will post screenshots tonight. Haven't had time to play around with timings yet as I just got them last night. More test coming tonight.
Awww, suppose I'll be sticking to my 7-8-7 1900 mhz 2 gb sticks then. These are good compared to most 1600 mhz ram, but slower than decent 2 gb sticks on X58.
Quote:
Originally Posted by Punisher!
For Sandybridge users set min and max FFT size to 720k as well as setting useable memory as suggested above. This picks up errors much quicker than a standard blend :).
Ok PiLsY
Ok Punisher!
Added Custom Prime95 run: According to linX available testing memory was 6.7gb. Set Custom memory to 6.7gb, and min/max FFT's to 720k. Ran over an hour just fine no errors!
http://i246.photobucket.com/albums/g...ustomPrime.jpg
http://i246.photobucket.com/albums/g...ustomPrime.jpg
Guys, someone just told me that these arent available new any more, surely this isnt true right? Can someone link me to the correct item in stock?
Can you link me to the Patriots you have?Quote:
Originally Posted by andressergio
:)
Very nice!!!
Quote:
Originally Posted by LagunaX
I think you mean these Patriot DDR3 2000's:Quote:
Originally Posted by aussie-revhead
http://www.newegg.com/Product/Produc...82E16820220535
http://www.ebay.com.au/itm/Patriot-P...item1e69740a97
Yeah that enough of a stability test for pretty much anything you can throw at it.
I run it overnight - mine always dropped out a thread (and the other 3 followed within 5 mins) between 6 and 8 hours on the custom test. Blend w/7000mb would run for 24 hours no hassle.
Even then though I got the odd issue booting up. A common one was typing in the windows password and getting a completely blue background screen and nothing more. Quick tap of reset and itd boot straight in and be fine all day. I dont think bios support is quite there yet on the 6 series chipsets for this ram.
Having said that the 1600mhz kits are vastly superior to the 1333mhz kit I got. I really would stick to the 1600mhz kits if anyone is considering buying.
Wonderful!
Was able to lower my voltage to 1.55vdimm for custom Prime95 6.7gb 720k fft's - 9-10-10-28 1T 2133:
http://i246.photobucket.com/albums/g...rime95155v.jpg
http://i246.photobucket.com/albums/g...rime95155v.jpg
Yeah thats sweet dude. Have you pushed bclk at all for 2200mhz?
My 2600k doesn't like anything over 100 for some reason, so no but happy with 9 10 10 28 2133.