Can I install a Bitspower Water Tank Z-Multi 400 upside down??

Hi there:

I am installing the Bitspower Water Tank Z-Multi 400 - POM (Model: BP-WTZM400P-BK). In the details of the product it refers to the bottom of the reservoirs having the 3 holes for choices of where to hook up the barbs or other fittings. And also refers to the top as having one additional hole to for fittings/fill ports etc...

I would like to use the bottom cap on top of the reservoir and the top cap as the bottom cap of the reservoir. I would like to run both inlet and outlet lines to the top and simply plug the bottom. Basically, I would be turning the reservoir upside down to use it. Can I do that???

There is a 3" metal tube connected to one of the holes. The metal tube is now on top of the reservoir and pointing down. I think I am supposed to use this as the outlet, but I'm not sure. I also tested putting a piece of 1/2" ID tubing over the metal tube and confirmed that it would fit and seal. I can run a small piece of tubing to the bottom area of the reservoir if you deem this necessary.

Are there any drawbacks to setting the reservoir up this way. Please enlighten me!!!

Thanks

well how would you fill it?

Yes, you can...but, I see some headaches to do so as they are mainly meant to either lay horizontal or have the 3 holes on the bottom. I've used several of those types of res's over the years and have always use the tube as the inlet so that the bubbles don't get sucked back into the loop. For your purposes though, it would have to be the outlet (and obviously below the water level) and to fill and bleed the case, it would have to be either on it's side or upside down.

Is there a special reason that has you looking at mounting it that way?

Hey guys:

I am using the Mountain Mods extended ascension case with the horizon back plate. This puts the mobo about 15" above the case floor. It's at a very nice height to run short lengths of hoses to the waterblocks and the radiators. Only the pumps are at the base of the case. I was thinking I can run a piece of hose to the bottom of the reservoir coming off the metal tube so the draw of the pump wouldn't be sucking up the air/water just entering the reservoir.

I think I'll have to fill the pump inlet tube to the brim and then connect it to the already filled reservoir to start the water loop.

I guess I could flip it over the right way, but, I need a bunch more hose and I didn't want to make the case look cluttered.

So what do you think??

Thanks

In that case a pictures worth a thousand words i can't picture it in my head.

Btw your not installing the pumps upside down are you?


*edit the more i think about it the.more.confused I get.on how you wanted it hooked up.
Sent from my X10a using Tapatalk

Here's a couple of pics:

The red hose in the reservoir is connected to the metal tube. I don't know why the pics are so big. Sorry about that. You'll get a close up!!! And, no, the pumps are not installed upside down.

Should I just go for it and give it a shot?

Thanks

I'm not sure it looks like that setup requires the pump to suck the water in instead of useing gravity. I'd be iffy on it.

I must say it makes me glad i had the panels of my MMA custom cut. So i didn't have to make a top/bottom mb choice.

Sent from my X10a using Tapatalk

I'm going to test this loop out with the upside down reservoir to see if it's going to do the job. I'll post back soon to let you know. Thanks for your input.

Res should always feed the pump. The way you have it now, it's going to be a real headache filling and bleeding, and then you may have problems with the tube between the rad and pump collapsing.

OT, what model YL's do you have on those GTX? Anything short of the SH's, I think you might be disappointed with your temps.

Hey Waterlogged:

I understand. That means I will have to re-think the loop. I'm not looking at it right now, but I will set it up that way. You'll here from me soon.

Edit:

So if that's the case, you have given me reason to flip the reservoir. I'll do that tomorrow and post back.

The Yate & Loons are the high speed 2000rpm fans. Please tell me they will do the job. Disappointment is NOT an option!!! I dumped enough $ into this project and I was planning on replacing them with better fans along the way. Please don't tell me how much noise 20 of them are going to make. I have a pretty good idea!!!

Thanks again for the advice.

oh wow I see the pic... wow that wont work...

Quote:

---

Originally Posted by jwmghf

The Yate & Loons are the high speed 2000rpm fans. Please tell me they will do the job. Disappointment is NOT an option!!! I dumped enough $ into this project and I was planning on replacing them with better fans along the way. Please don't tell me how much noise 20 of them are going to make. I have a pretty good idea!!!

Thanks again for the advice.

---

You got the right model. :up: Any RPM's above 1700-1900 should provide reasonably good temps. Anything below that to about 1400RPM's will be about as good as you would be able to get with a low FPI rad, and don't even bother going below 1400. ;)

I'm much better now!!! I'll change the order of the loop and let you know how I make out. I have to say,... You're very observant and thanks for that!! I'll work on the re-route tomorrow and post back promptly. The next couple of days are busy for me, but I'll be back for sure!!!

Hey guys:

It works like a champ upside down!!! Thanks for the heads up about the res. feeding the pump. I learned something new!!!

Pictures, please.

They way you say that, it makes me think you're having the pump suck the water up out of the top of the reservoir, even though the pump is mounted below the reservoir. Makes no sense.

The pictures were in post six. ...

Sent from my X10a using Tapatalk

You said you changed the routing so the reservoir fed the pump, but in your pictures, it doesn't. You missed one of the key set up rules for watercooling... the reservoir must output to the pump.

Also, you really need to re-size those pictures.

The posts if read in sequence have him asking, me asking for pics, and waterlogged giving him his solution. then him changing it.

I think you fourms reader is buggy.

Sent from my X10a using Tapatalk

Hey guys:

I did change the hose setup to have the reservoir feed the pump. The reservoir upside down with a piece of 1/2" ID tubing running down off of the 3" metal tube that came with the reservoir. It's working fine and I could leave it the way it is, but, I may opt to flip it over and have the res. installed the way it was called for. The reasoning for this being stated by Waterlogged in his opening comments. I am working on a strategy to use as little hose as possible. If I can do it with them in there normal upright position, I will make the change.

I'm confused. Pictures?