how high can they go?
How much volts can they take?
at 3.34v Vmem 1.63v Vtt
250 2-2-2-5 1:1(on air right now.)
Is 3.34v safe for 24/7
Printable View
how high can they go?
How much volts can they take?
at 3.34v Vmem 1.63v Vtt
250 2-2-2-5 1:1(on air right now.)
Is 3.34v safe for 24/7
I whould say 3.6V safe for 24/7 w/ resonnable cooling....
And do you have the 250FSB wall?
I don't think there is a wall. 250 is 3.5ghz i think my max on stock air.
But I've heard that sometimes they even go to 270FSB.
I just hope I dont have that wall on mine.....
I didn't even know it's possible for ch-5 to do 250 at 2-2-2-5...
my XMS3200LL did do 240.
My CH-5 CANNOT do 2-2-2 timings. Even @ 2.9V it doesn't do 200 FSB.
Actually ivan with the newer batches of CH-5 Thats no longer true. Theres a couple screenshots of 2-2-2 at something like 230. It takes a lot of voltage though, something like 3.3 or more.
Edit, sorry didn't notice the my at the start of your sentence.
over 3.3v 1.6v for me and then they started doing something. ps holding me back now. can only go to 3.36v under load.
I have some noname CH5 :stick: :D (Ithink i have a 250fsb 1-1 wall :slapass:
It runs 3D01/03/Spi/Hexus @ 249fsb 1-1 5-2-2-2 (3.3v):slobber:
But @ 250fsb 1-1 5-2-2-2 i get HD corruption:mad:
Also does 283fsb @ 5/4 >5-2-2-2 (3.3v):toast:
---------------------------------------------------------------
245fsb 1-1 5-2-2-2 >pc3200
V's
260FSB 1-1 5-4-3-2 >pc4000
5-2-2-2 @ 15fsb less won in everytest i ran:eek: :smileysex
you need more Vtt and or Vmem and maybe Vdd.
wow I need to get some of that ch5 ram thatll own bh5! mine isnt too bad, 220fsb at 2-2-3-11 at 3 volts(cant go lower, dont want to reverse the mod) I can do up to 3.25v on my nf7-s whats the odds of me getting some corsair value for 240+ fsb at 2-2-2-11 dual channel goodness?
it will never own BH-5. Didn't you know that BH-5 can do 290fsb+ at 2-2-2-5-9-16 and 3.5-3.7V? :stick:Quote:
wow I need to get some of that ch5 ram thatll own bh5!
stestan: The wall is that it CANT pass 250FSB not MHz. ex: Like that they cant do 250FSB at 185MHz....
But my CH5 are new and can do AT LEAST 236MHz, 2-2-2-6, 3.2V
But I dunno about the wall(CPU was maxed out). Now I have my 2.4C M0 and vid card so I can test it in 2-3 days....
skate, the 250 FSB "wall" is only on intel systems ;)
But stestan is an Intel:p:
but Illicit Tweakin isnt :D :)
I think theyres no XP CH5 wall coze they cant go up to 250FSB:D
Here is my Ch-5
It was bought in early 2003, think the date is 0309.
This is at 3.2v and in my dfi.
I do seem to have a 250 wall.
i dont think all BH-5 will. my Corsair has a hard time staying at 260 with 3.6v.Quote:
Originally posted by QuadDamage
it will never own BH-5. Didn't you know that BH-5 can do 290fsb+ at 2-2-2-5-9-16 and 3.5-3.7V? :stick:
that stick of 3200LL CH-5 i had seemed to perform almost the same as the 3500C2 BH-5 stuff i got now. both take about 2.8/9v to get to 220 tight, 3.1v for 230 and 3.3v for 240. i didnt have any Vmods with the CH-5 though. it may have done 250 with some more volts.
Mine are 03/11. And I think the CH5's can pass the wall w/ alot of volts....
ive seen people run 3.6-3.75 on these forumsQuote:
Originally posted by Illicit Tweakin
how high can they go?
How much volts can they take?
at 3.34v Vmem 1.63v Vtt
250 2-2-2-5 1:1(on air right now.)
Is 3.34v safe for 24/7
dunno if thye use active cooling lol
freind of mine had them running pretty nice on 3.4v, and then woke up one day....DEAD. CH-5 cannot handle voltage as well as BH-5. just remember that and be careful unless you could care less ;)
I am now just haven't changed sigQuote:
Originally posted by enzoR
but Illicit Tweakin isnt (on intel)
I've got some CH5 that did 240 11-2-2-2 @ 3.3v
I didn't try further...
I now have a locked Barton that won't "even" do 11.5x240 ;) lol
I hit the wall with the cpu @ 11.5x229 :(
Anyway, now running the memory 24/7 @ 3.3v :) no problems whatsoever :)