Printable View
Hey everyone,
Just wanted to check if EK, BP, Koolance, or anyone else has any plans for a full cover water-block for the upcoming Gigabyte GA-X58A-OC board (seen below)?
http://limages.vr-zone.net/body/11262/1-0.png
I really hope there is something in the works because I am seriously considering moving to this board.
:)
OT, but I think the stock heatsink is very nice and should perform a lot better than Classified's crap (X58A-OC has pretty much the best heatsink I've seen on X58 boards). I don't think waterblock is going to be necessary.
But I bet we'll see a few waterblocks. If it's indeed priced @ $280 it's going to be extremely popular.
It's not about necessary, it's about function and appearance. When watercooling everything has to go under water. No ifs or buts ;) :)Quote:
Originally Posted by zalbard
I personally don't do air cooling any more.
Honestly if I were a block manufacturer I would be skipping on this board. It is a board designed for benching, not day-to-day use. Designing a full cover for this block just doesn't make a whole lot of sense when most people will be using it w/ LN2 anyways.
:down: Stop giving them negative ideas :(Quote:
Originally Posted by lowfat
Really? Not a single vendor reply with "Yes" or "No"? Really?! :shrug:
First the board isn't even available yet so they probably have not had a chance to look at it in person. Second not all manufacturers post on here and they dont spend all day surfing the forums looking for boards to make blocks for. Third there is really no point as this board is meant for LN2 and not water cooling.
ur going to hurt my E759's feelings.Quote:
Originally Posted by Planet
Thats what they said, but we still have them. :rofl:
Serious note, im with planet tho, its not to the best interest of board makers to make this block.
Its honestly too late, a very late move on giggy's part.
This is (extreme) benchmarking motherboard, not 24/7 gamer/workstation board.
so....yes?Quote:
Originally Posted by tiborrr
pretty please make it not have a rubbish huge EK logo, and what is with EK's putting aluminium plate over the Nickel Plexi blocks? Serious question!
Same was said about the E759...so what's the answer?Quote:
Originally Posted by tiborrr
OT: There is also nothing wrong with this board as a 24/7 board (not every board has to be overloaded with junk features), and some of us benchmark on water too, just as an FYI. Further to this, I believe you are EK affiliated so you could use a bit more professionalism in your answers :) If you have no plans on making it a "we will not be supporting this board as it is, in our view, not intended as a board for daily use" would have sufficed. Just a tip for the future ;)
If it is going to be indeed sold at $280 then I will see a lot of people buying it.
If not EK, then I guess someone else will chime in...
bump!
Wow, still nobody to reply... :(
that is a good pointQuote:
Originally Posted by dejanh
I'd love to see a waterblock design for this motherboard, even if it is designed as a benchers board that's not to say you won't be running everything on a chiller or phase.
However the biggest unknown is how many of these boards GBT will be making and if they treat it as a limited edition type product. (UD9 anyone) If that is the case then block makers will be hard pressed to sell enough product to make a production run worth while.
I still vote yes, make the block, build it and they will buy.
this will last till socket2011 and depending on what happens with CB it might last for another few years :rofl:
Indeed. If I could get a waterblock for this board I'd snap it up in a second to replace my current board. I really hope somebody jumps on this. I was also thinking to maybe get the CPU under Phase and leave the motherboard and GPUs under water as this board would be really easy to work with...Quote:
Originally Posted by redmax
The board isn't really even released yet, we have yet to see how many of these boards will actually be manufactured and if the infos about the pricing will hold water. I believe it's too soon to draw any conclusions :)
That's what I like to hear :D An outright no was rather disconcerning ;)Quote:
Originally Posted by tiborrr
I plan to game on the system that I build with this mobo. :up:Quote:
Originally Posted by tiborrr
Got the board drawn in CAD already! :up: Block is under development!
What aluminum plate? The plates are stainless steel! :)Quote:
Originally Posted by zeropluszero
ok, so SS, why are they there?Quote:
Originally Posted by tiborrr
But where do we get the board here inn Europe??
Does anyone have it anywhere where they ship international?
OMG! OMG! OMG! OMG! OMG! YEEEESSSSSSSSSS! :woot::buddies:Quote:
Originally Posted by tiborrr
Now that is so, so, so good to hear. Now for this board to hit retail and we are in business! :up:
Any ideas when you expect the production block to be available? I just want to plan the rebuild adequately ;)