Help w/ Vdimm MOD [Albatron KX18ds motherboard]

Printable View

06-16-2005, 06:54 AM
andlcs

Help w/ Vdimm MOD [Albatron KX18ds motherboard]

Hi, I'm looking for the Vdimm + VTT mod for Albatron KX18DS Pro motherboard (please note it's not KX18D model VMEM MOD. These 2 models are very similar but KX18DS is shorter [doesn't have 9 screws])

Information:
Photos | PHOTOS 2 | PHOTOS 3

http://www.geocities.com/a_andlcs/KX18DS/Albyvmem.JPG

http://www.noticias3d.com/articulos/...es/memoria.jpg

DATASHEETS:
APL5331: http://www.anpec.com.tw/products/dow...31/APL5331.htm

APM4500:
http://www.alldatasheet.com/datashee...C/APM4500.html

APW7058:
http://www.anpec.com.tw/products/dow...58/apw7058.htm

RT9174:
http://www.richtek-ic.com.tw/Product...DS9174-00P.pdf

LM358:
http://www.national.com/pf/LM/LM358.html

Quote:

LM358
44A
Z8Y6

If U need more information I'll search

Thank You.
06-16-2005, 06:04 PM
andlcs

http://www.geocities.com/a_andlcs/KX18DS/alby.JPG
06-16-2005, 06:28 PM
Malves

Does U358 have 8 pins? Anyway you can get a close up pic of it?

If it does have 8 pins, can you check voltage readings on pin 1 and 7?
06-16-2005, 06:34 PM
andlcs

Quote:

Originally Posted by Malves

Does U358 have 8 pins? Anyway you can get a close up pic of it?

If it does have 8 pins, can you check voltage readings on pin 1 and 7?

Hi Malves.
Now I read the letters w/ a flashlight

The IC is
LM358
44A
Z8Y6

Already edited the first post...

Please tell me which pins to check voltage readings.

Thanx
06-16-2005, 06:47 PM
Malves

pin 1 and pin 7. Also, try to find the vdimm FET - those 2 close to the dimm slots.
06-16-2005, 07:32 PM
andlcs

http://www.geocities.com/a_andlcs/KX18DS/vdimmcheck.JPG

I'll measure the others voltages tomorrow because i'm going to have to remove the motherboard from the case.

What about Direct Vdimm mod (conecting 3.3V from PSU)? Is it the same in all boards?
06-16-2005, 07:42 PM
Malves

I never recommend vdimm=vio mod. LM358 is the chip we want for the mod. I just need those reading to tell you the pin for the mod and the trimmer value.
06-17-2005, 02:44 AM
mike047

HI,
Does this board run off the 5v rail like the KX18D?

Thanks,
mike
06-17-2005, 04:45 AM
andlcs

LM358:

PIN 1 : 5.8V
PIN 7 : 5.5V

Weird voltages. Pin 1 is where the ic has a little circle and a stripe right?

4 3 2 1
| | | |
------
|358º|
------
| | | |
5 6 7 8

Is this correct?
06-17-2005, 05:09 AM
andlcs

Quote:

Originally Posted by mike047

HI,
Does this board run off the 5v rail like the KX18D?

Thanks,
mike

For the CPU?

Yes.
06-17-2005, 11:37 AM
mike047

Quote:

Originally Posted by andlcs

For the CPU?

Yes.

HI, My question was in regard to the memory.

mike
06-17-2005, 04:53 PM
andlcs

Sorry Mike I don't know the answer.

http://www.geocities.com/a_andlcs/KX18DS/lm358.JPG
06-18-2005, 01:56 AM
mike047

HI,
I was interested as I have Vdimm modded two KX18D per MALVES scholarship.
They work off the 5V rail and will go as high as the PSU produces. I have not been able, recently, to obtain more KX18D's so I am interested in the "DS" model like you have.

When you are sucessful, I will buy a couple and try it out:D

[I am working on a Gigabyte GA7N400L today:D]
06-18-2005, 05:22 AM
persivore

Can you check the resistance between pin 2 and ground, and pin 6 and ground please.
If you want to find out which voltage the Vdimm supply is supplied from, check the voltage at the rear tab of the Vdimm MOSFET.
06-18-2005, 08:07 AM
andlcs

Quote:

Originally Posted by persivore

Can you check the resistance between pin 2 and ground, and pin 6 and ground please.
If you want to find out which voltage the Vdimm supply is supplied from, check the voltage at the rear tab of the Vdimm MOSFET.

Hi persivore,
Resistance:

PIN 2 + Ground = 2.4K
PIN 6 + Ground = 0 ohm

Mosfets voltages:
http://www.geocities.com/a_andlcs/KX18DS/mosfet.JPG

These 3 points are VDIMM Check points:
http://www.geocities.com/a_andlcs/KX...dimmcheck2.JPG
06-18-2005, 10:14 AM
persivore

Try connecting a 50k VR between pin 2 and ground. Decrease resistance for more voltage. It looks like the Vdimm is supplied by the 3.3v rail, so you will have to increase your 3.3v rail if you want to run high Vdimm.

Note: XS owners and members will not be liable for any damage caused to you or your hardware, neither can be liable for any breach of the warranty.
06-18-2005, 10:30 AM
Malves

Thanx for the help, bro.:)
06-18-2005, 02:03 PM
andlcs

Thank You persivore
Thank You Malves

I'll try the mod as soon as my 25 turn pot arrives.
07-02-2005, 05:52 AM
David Coleman

How is this board different from the KX18D Pro II?
07-13-2005, 10:32 PM
wedfighter

Quote:

Originally Posted by David Coleman

How is this board different from the KX18D Pro II?

it equipped with MCP-RAID southbridge
so it's not using a Sil Image anymore to host the SATA drive
afaik the CL timing in BIOS cant be more aggressive than 2,5 (not like the KX18D Pro which has the CL 2 option in BIOS)
anyone know the link for modded BIOS to enable the CL2 timing?
08-04-2005, 05:24 AM
David Coleman

no CL2? That's really strange!
What are the Vdimm options?
08-12-2005, 09:02 AM
andlcs

Quote:

Originally Posted by David Coleman

no CL2? That's really strange!
What are the Vdimm options?

2.7V
2.8V
2.9V
3.0V

And no CL2 : (
08-13-2005, 02:18 PM
David Coleman

If you run BH5 or TCCD at SPD does it run CL2?

Those are the same vdimm options as the KX18D Pro II.
08-17-2005, 04:29 AM
wedfighter

even when we run SPD for those sticks of memory, CL wont tighter than 2,5
except if we Cbid-ed them to CL2 (under windows)
08-19-2005, 10:30 AM
andlcs

David Coleman, in the Albatron forum they said if the memory is CAS2 by SPD it will run at CAS2. Mine UTT is CAS2.5 by SPD so I can't test.

One interesting thing is that CPU-Z reads CAS2-3-3-11 when I set CAS2.5-3-3-11
http://valid.x86-secret.com/show_oc?id=23036

wedfighter, how do you change CAS on by software? I thought it could not be changed after the memory count.
08-19-2005, 04:07 PM
wedfighter

Quote:

Originally Posted by andlcs

David Coleman, in the Albatron forum they said if the memory is CAS2 by SPD it will run at CAS2. Mine UTT is CAS2.5 by SPD so I can't test.

One interesting thing is that CPU-Z reads CAS2-3-3-11 when I set CAS2.5-3-3-11
http://valid.x86-secret.com/show_oc?id=23036

wedfighter, how do you change CAS on by software? I thought it could not be changed after the memory count.

I'm using CBid 750
03-15-2006, 01:43 PM
andlcs

Hello, I finally did the mod but it didn't work. VDIMM voltage remains the same when I decrease resistance.

I tried connecting the VR 50k in pin 2 of LM358 and ground, the board booted fine but VDIMM did not increase. Then, I tried Pin 6 and Ground, same thing happened...

Couple of pictures:
http://www.geocities.com/a_andlcs/KX...ngVDIMM_01.JPG

http://www.geocities.com/a_andlcs/KX...ngVDIMM_02.JPG

What's wrong?

Thanks
03-17-2006, 03:04 PM
mike047

What model/revision is the board??

edit, I see in the first photo that it is a "DS", I don't believe the vmod works on that model. The plain"D" does, as I have modded several.

mike

I just realized that I had replied to this thread a long time ago, it's rough getting old:D
03-17-2006, 03:27 PM
Hell-Fire

Shouldn't matter what model the board is as long as the regulators are the same.
03-17-2006, 03:29 PM
mike047

Quote:

Originally Posted by Hell-Fire

Shouldn't matter what model the board is as long as the regulators are the same.

I didn't know that, Thanks
03-17-2006, 07:44 PM
andlcs

I re-checked the resistance and voltages:

LM358
PIN2 + GND: 2.5k
PIN6 + GND: 100 Ohm

PIN1: 5.9V
PIN2: 3.0V
PIN3: 3.0V
PIN4: 0.0V
PIN5: 3.6V
PIN6: 3.6V
PIN7: 5.4V
PIN8: 12.0V

Is that the right VDIMM chip?
03-18-2006, 02:23 AM
mike047

The mod that I did on my KX18D was to place the trimmer between pins 3&6.
This was according to Malves mod on his site.

http://malvescorner.net/kx18.html

The IC you are working with on your board is a LM358, the one on the KX18D is a RT9202. My information is not of any value to your board.

Maybe some one with recent electronic experience will come by and help out. My technology is from the late 60's and I never worked as an engineer:(

All times are GMT -8. The time now is 01:01 AM.

XtremeSystems